2007-2013 Highlander Kluger · Service Manual SECURITIES

B2784 Antenna Coil Open / Short

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The transponder key coil is built into the transponder key amplifier and receives a key code signal from the transponder chip in the key. This signal is amplified by the amplifier, then it is output to the transponder key ECU assembly.
DTC No.
DTC Detection Condition
Trouble Area
B2784
Antenna coil is open/shorted
  1. Wire harness or connector
  2. Transponder key amplifier
  3. Transponder key ECU assembly

WIRING DIAGRAM

B164252E07

INSPECTION PROCEDURE

NOTICE:
If the transponder key ECU is replaced, register the key and ECU communication ID.


1. READ VALUE ON INTELLIGENT TESTER (TRANSPONDER KEY AMPLIFIER)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Select Antenna Coil Status in the Data List and read the tester display.

    Immobiliser (Transponder Key ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Antenna Coil Status
    Transponder key amplifier coil condition/NORMAL or FAIL
    NORMAL: Antenna coil is normal
    FAIL: Antenna coil is malfunctioning
    -

    OK:
    NORMAL (Antenna coil is normal) appears on the screen.



NG
Go to step 2
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

2. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)

  1. B151012E06
    Disconnect the transponder key ECU and transponder key amplifier connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-4 (TXCT) - D24-5 (TXCT)
    Always
    Below 1 Ω
    D37-5 (AGND) - D24-7 (AGND)
    Always
    Below 1 Ω
    D37-14 (VC5) - D24-1 (VC5)
    Always
    Below 1 Ω
    D37-15 (CODE) - D24-4 (CODE)
    Always
    Below 1 Ω
    D37-4 (TXCT) - Body ground
    Always
    10 kΩ or higher
    D37-5 (AGND) - Body ground
    Always
    10 kΩ or higher
    D37-14 (VC5) - Body ground
    Always
    10 kΩ or higher
    D37-15 (CODE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT TRANSPONDER KEY ECU ASSEMBLY (TRANSPONDER KEY AMPLIFIER POWER SOURCE)

  1. B128338E30
    Reconnect the transponder key ECU and transponder key amplifier connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D37-14 (VC5) - Body ground
    No key is in ignition key cylinder
    Below 1 V
    D37-14 (VC5) - Body ground
    Key is in ignition key cylinder
    4.6 to 5.4 V



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK


4. INSPECT TRANSPONDER KEY ECU ASSEMBLY (TRANSPONDER KEY AMPLIFIER GROUND)

  1. B128338E32
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D37-5 (AGND) - Body ground
    Always
    Below 1 Ω



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

REPLACE TRANSPONDER KEY AMPLIFIER (Click here)


← B2784 Antenna Coil Open / Short (Aug 2008 – Jun 2010)B2793 Transponder Chip Malfunction (from May 2007) →