2007-2013 Highlander Kluger · Service Manual SECURITIES

DATA LIST / ACTIVE TEST

System information · Vehicles built from May 2007


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to the ON position.

  3. Turn the tester on.

  4. Read the Data List according to the display on the tester.

    Immobiliser (Transponder Key ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key SW
    Unlock warning switch signal/ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -
    IG SW
    Ignition switch signal/ON or OFF
    ON: Ignition switch ON or START
    OFF: Ignition switch ACC or OFF
    -
    Immobiliser
    Immobiliser system status/SET or UNSET
    UNSET: Ignition switch ON
    SET: Without key
    -
    Permit (Start)
    Permit (Start) signal/OK or NG
    NG: No permission for engine start
    OK: Engine start permission
    -
    Response
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Frame Error
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Different Serial Number
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Different Encrypt Code
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Abnormal Status
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Bcc Malfunction
    Transponder chip data/NG or OK
    NG: Incorrect data being sent
    OK: Correct data being sent
    -
    Sub Key
    Sub key code signal/NOMATCH or MATCH
    NOMATCH: Non-matching sub-key code is sent
    MATCH: Sub-key code is sent
    -
    Master Key
    Master key code signal/NOMATCH or MATCH
    NOMATCH: Non-matching master key code is sent
    MATCH: Master key code is sent
    -
    Transponder S-Code
    Number of registered sub key/min. 0, max. 15
    Number of registered sub-key
    -
    Transponder M-Code
    Number of registered master key/min. 0, max. 15
    Number of registered master key
    -
    Reg Code Space Full
    Memory space for key codes registration/NOT FULL or FULL
    NOT FULL: More key code registration possible
    FULL: No more key code registration possible
    -
    +B
    Power source/BRAKE or NORMAL
    BRAKE: Power source open
    NORMAL: Power source normal
    -
    Antenna Coil Status
    Transponder key amplifier coil condition/NORMAL or FAIL
    NORMAL: Antenna coil is normal
    FAIL: Antenna coil is malfunctioning
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to the ON position.

  3. Turn the tester on.

  4. Perform the Active Test according to the display on the tester.

    Immobiliser (Transponder Key ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indic
    Security indicator light
    ON/OFF
    -

← DTC CHECK / CLEAR (from May 2007)DIAGNOSTIC TROUBLE CODE CHART (May 2007 – Jul 2008) →