After the ignition switch is turned off, the navigation receiver assembly (HDD navigation system) records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal (Click here).
2.
RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
Start the engine.
Turn the A/C switch on.
Operate the cooler compressor at an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
3.
POSITION FRONT WHEELS STRAIGHT AHEAD
4.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent the airbag from deploying (Click here).
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Make sure to select FACE mode before disconnecting the cable from the negative (-) battery terminal.
5.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
Remove the nut, and the front wiper arm and blade assembly LH.
6.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
Remove the nut, and the front wiper arm and blade assembly RH.
7.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Disengage the 2 claws and disconnect the front fender to cowl side seal LH.
Disengage the 2 claws and disconnect the front fender to cowl side seal RH.
Remove the 2 clips.
Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.
8.
REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Disconnect the connector.
Remove the 4 bolts, and the windshield wiper motor and link assembly.
9.
REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY
Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.
Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.
10.
DISCONNECT HEATER OUTLET WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.
NOTICE:
Do not apply excessive force to the heater outlet water hose.
Prepare a drain pan or cloth in case the coolant leaks.
11.
DISCONNECT HEATER INLET WATER HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater inlet water hose.
NOTICE:
Do not apply excessive force to the heater inlet water hose.
Prepare a drain pan or cloth in case the coolant leaks.
12.
DISCONNECT COOLER REFRIGERANT LIQUID PIPE A
Remove the bolt, and slide the hook connector.
Disconnect the cooler refrigerant liquid pipe A.
Remove the O-ring from the cooler refrigerant liquid pipe A.
NOTICE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.
21.
REMOVE COMBINATION METER ASSEMBLY
Remove the 4 screws.
Disconnect the connector and remove the combination meter assembly.
22.
REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.
23.
REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.
NOTICE:
Do not pull on the small storage compartment lid. Doing so may cause damage.
Disconnect each connector and remove the center instrument cluster finish panel assembly.
24.
REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.
NOTICE:
Do not pull on the small storage compartment lid. Doing so may cause damage.
Disconnect each connector and remove the center instrument cluster finish panel assembly.
25.
REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)
Disengage the 4 clips and remove the heater control and accessory assembly.
Disconnect the connector.
26.
REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
Disengage the 4 clips and remove the air conditioning control assembly.
Disconnect the connector.
27.
REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)
Remove the 4 bolts.
Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the radio receiver assembly with bracket.
28.
REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
Remove the 4 bolts.
Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.
Disconnect each connector and remove the navigation receiver assembly with bracket.
29.
REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)
Remove the 4 bolts <D>.
Disengage the 4 clips.
Disconnect each connector and remove the integration control and panel assembly with bracket.
30.
REMOVE MULTI-MEDIA INTERFACE ECU WITH BRACKET
Disconnect each connector.
Remove the 3 nuts and multi-media interface ECU with bracket.
31.
REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 8 claws and guide, and remove the front door scuff plate LH.
32.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Remove the clip.
Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.
Remove the No. 2 console box duct as shown in the illustration.
41.
REMOVE LOWER REAR CONSOLE BOX
Remove the lower rear console box.
42.
REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)
Remove the 4 bolts and 2 screws.
Disengage the 6 claws and remove the console box assembly.
43.
REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)
Remove the 4 bolts and 2 screws.
Disconnect the connector.
Disengage the 6 claws, and remove the console box assembly.
44.
REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for LHD)
Using a clip remover, remove the 2 clips.
Remove the 3 screws <E>.
Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.
45.
REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for RHD)
Using a clip remover, remove the clip.
Remove the 3 screws <E>.
Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.
46.
REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD)
Using a clip remover, remove the clip.
Remove the 3 screws <E>.
Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.
47.
REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)
Using a clip remover, remove the clip.
Remove the 3 screws <E>.
Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.
48.
REMOVE ENGINE SWITCH (w/ Smart Entry and Start System)
Disconnect the switch connector.
Disengage the 2 claws and remove the switch.
49.
DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
50.
REMOVE FRONT PILLAR GARNISH LH
Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
HINT:
Make the front pillar garnish LH hang down from the front pillar garnish clip.
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.
NOTICE:
Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
Replace the front pillar garnish clips with new ones if they are removed from the vehicle.
Disengage the 3 guides at the front end of the front pillar garnish LH and remove it.
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
51.
DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure for the RH side and the LH side.
52.
REMOVE FRONT PILLAR GARNISH RH
Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
HINT:
Make the front pillar garnish RH hang down from the front pillar garnish clip.
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish RH.
NOTICE:
Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
Replace the front pillar garnish clips with new ones if they are removed from the vehicle.
Disengage the 3 guides at the front end of the front pillar garnish RH and remove it.
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.
56.
REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
HINT:
Use the same procedures for the RH side and the LH side.
57.
DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY
Disconnect the connector.
58.
REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Disconnect each connector.
Remove the 2 passenger airbag bolts <A>.
Disengage each clamp.
Remove the 2 clips.
Remove the 2 bolts <D> and nut <G>.
Disengage the 5 claws and remove the instrument panel safety pad assembly.
59.
REMOVE BRAKE PEDAL RETURN SPRING
Remove the brake pedal return spring from the push rod pin and instrument panel reinforcement.
60.
REMOVE STOP LIGHT SWITCH ASSEMBLY
Disconnect the connector.
Loosen the stop light switch lock nut.
Remove the stop light switch assembly as shown in the illustration.
61.
SEPARATE BRAKE MASTER CYLINDER PUSH ROD CLEVIS
Remove the clip and push rod pin, and separate the brake master cylinder push rod clevis from the brake pedal sub-assembly.
62.
REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for LHD)
Disconnect the brake pedal load sensing switch connector and disengage the clamp.
Remove the 2 bolts and separate the brake pedal support sub-assembly from the instrument panel reinforcement.
Remove the 4 nuts and brake pedal support sub-assembly from the body.
63.
REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)
Disconnect the brake pedal load sensing switch connector and disengage the clamp.
Remove the 2 bolts and separate the brake pedal support sub-assembly from the instrument panel reinforcement.
Remove the 4 nuts and brake pedal support sub-assembly from the body.
64.
REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY
Remove the 4 bolts.
Disengage the 2 hooks.
Pull out the driver side knee airbag assembly from the vehicle and support the driver side knee airbag assembly with one hand as shown in the illustration.
NOTICE:
When removing the driver side knee airbag assembly, do not pull the airbag wire harness.
Using a screwdriver with the tip wrapped with protective tape, disconnect the driver side knee airbag connector.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
Disengage the 2 claws and separate the DLC3 from the driver side knee airbag assembly.
65.
REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY (for LHD)
Disengage the 2 claws and remove the No. 1 air duct sub-assembly.
66.
REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD)
Disengage the 2 claws and remove the No. 1 air duct sub-assembly.
67.
SEPARATE STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY
Loosen the bolt.
Remove the bolt and slide the steering intermediate shaft sub-assembly.
NOTICE:
Do not separate the steering intermediate shaft sub-assembly from the power steering link assembly.
Put matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.
Separate the steering intermediate shaft sub-assembly from the power steering link assembly.
68.
REMOVE STEERING COLUMN ASSEMBLY (for LHD)
Disconnect the connector from the power steering ECU assembly.
HINT:
As shown in the illustration, turn the lock lever to disconnect the connector.
Disconnect the connector from the power steering ECU assembly.
Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.
Remove the bolt, 2 nuts, and the steering column assembly.
69.
REMOVE STEERING COLUMN ASSEMBLY (for RHD)
Disconnect the connector from the power steering ECU assembly.
HINT:
As shown in the illustration, turn the lock lever to disconnect the connector.
Disconnect the connector from the power steering ECU assembly.
Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.
Remove the bolt, 2 nuts, and the steering column assembly.