2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSTALL NO. 1 COOLER THERMISTOR

  1. E151029E01
    Install the No. 1 cooler thermistor as shown in the illustration.
    Part
    Length
    A
    34.3 mm
    1.35 in.
    B
    20.9 mm
    0.82 in.
    C
    50 mm
    1.96 in.

    NOTICE:
    1. Be sure to insert the thermistor only once because reinserting it into the same position will not allow it to be firmly secured.
    2. When reusing the evaporator, insert the thermistor one row next to the one that has been used previously (X in the illustration).
    3. After inserting the thermistor, do not apply excessive force to the wire.
    4. Directly insert the thermistor until the edge of plastic case "a" comes into contact with evaporator "b".


2. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

  1. E151027
    Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces.

  1. Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. E151026
    Install the No. 1 cooler evaporator sub-assembly.

  1. Engage the clamp.

  1. E151025
    Engage the 5 claws.

  1. Install the plate cover with the 6 screws.

  1. Connect the connector.


3. INSTALL COOLER EXPANSION VALVE

  1. E151024
    Using a 4 mm hexagon wrench, install the cooler expansion valve with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


4. INSTALL ASPIRATOR (for Manual Air Conditioning System)

  1. E151022
    Engage the 2 claws and install the aspirator.


5. INSTALL ASPIRATOR (for Automatic Air Conditioning System)

  1. E151023
    Engage the 2 claws.

  1. Engage the clamp and install the aspirator.


6. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

  1. E151021
    Install the heater radiator unit sub-assembly as shown in the illustration.


7. INSTALL HEATER CLAMP

  1. E151019
    Install the clamp with the screw.

  1. Engage the 3 claws and install the heater clamp.


8. INSTALL FRONT AIR MIX CONTROL SERVO MOTOR SUB-ASSEMBLY

  1. E151018E01
    Using the reference point, install the front air mix control servo motor sub-assembly with the 2 screws.

  1. Connect the connector.


9. INSTALL FRONT AIR OUTLET CONTROL SERVO MOTOR SUB-ASSEMBLY

  1. E220371
    Check that the slots, links and gears of the front air outlet control servo motor sub-assembly are positioned in the correct orientation as shown in the illustration.

  1. Face the contact surfaces of the front air outlet control servo motor sub-assembly and air conditioning radiator assembly for the front air outlet control servo motor sub-assembly upward.

  1. Rotate the link of the air conditioning radiator assembly all the way to the left as shown in the illustration.

    E219270

  1. Rotate the link of the air conditioning radiator assembly to the bottom as shown in the illustration and confirm that the mode switching duct hole is fully closed.

    E219271E01

  1. Rotate the lever of the air conditioning radiator assembly to the top as shown in the illustration.

    E220372

  1. Rotate the link of the air conditioning radiator assembly to the in-line position as shown in the illustration.

    E220373E01

  1. E219274E01
    Wrap the upper and lower links with vinyl tape to hold them in the in-line position.

  1. Install the link of the front air outlet control servo motor sub-assembly to the link guide pin (A) of the air conditioning radiator assembly as shown in the illustration.

    E220374E03

  1. Install the guide hole of the front air outlet control servo motor sub-assembly to the guide pin of the air conditioning radiator assembly as shown in the illustration.

  1. Temporarily install the screw (up to 4 or 5 threads).

    NOTICE:
    1. Make sure that the link guide pin (B) is inserted in the front air outlet control servo motor sub-assembly slot.
    2. Avoid tilting the front air outlet control servo motor sub-assembly during installation. This helps to prevent the guide pins from coming out of position.

  1. E219276
    Lift the front air outlet control servo motor sub-assembly slightly to create clearance.

  1. Move the air conditioning radiator assembly gear so that alignment holes of the front air outlet control servo motor sub-assembly and air conditioning radiator assembly are aligned.

    E219277E03

  1. E219278
    Insert a screwdriver into the aligned holes as shown in the illustration.

  1. Make sure that all the links and gears are in the positions shown in the illustration.

    E220477E03

  1. E219280
    Push the loose fitting front air outlet control servo motor sub-assembly into position.

    NOTICE:
    1. Make sure that the front air outlet control servo motor sub-assembly is fully pushed into position.
    2. After pushing the servo into position, keep it in place by holding it until the screws are installed.

    HINT:
    Push the front air outlet control servo motor sub-assembly until a click sound is heard.

  1. Remove the screwdriver.

  1. E220478
    Fully install the top screw, and then install the front air outlet control servo motor sub-assembly with the 2 remaining screws.

  1. Remove the vinyl tape.

  1. E220355
    Connect the 2 connectors.


10. INSTALL BLOWER ASSEMBLY

  1. E151015
    Engage the 2 claws.

  1. Install the blower assembly with the 2 screws.

  1. Connect the connector.


11. INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)

  1. E151068
    Install the quick heater assembly as shown in the illustration.

  1. Install the 3 screws.


12. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

  1. E151013
    Engage the 3 claws and install the No. 3 air duct sub-assembly as shown in the illustration.

← DISASSEMBLY (from May 2007)INSTALLATION (May 2007 – Jul 2008) →