2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

AUTO, OFF, TEMP UP (+), and TEMP DOWN (-) switches are located on the steering pad switch. The resistance of the steering pad switch changes in accordance with switch operation. The air conditioning control assembly outputs voltage to the steering pad switch and reads voltage changes due to the resistance changes that result from switch operation.

HINT:
If there is an open in the circuit, the air conditioning system cannot be operated by the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same as if the switch were continuously depressed. Therefore, the air conditioning control assembly cannot be operated by the steering pad switch assembly, and the air conditioning control assembly will not be able to function correctly.


WIRING DIAGRAM

E153719E03

INSPECTION PROCEDURE


1. INSPECT AIR CONDITIONING CONTROL ASSEMBLY

  1. E153885E04
    Remove the air conditioning control assembly (Click here) with the connectors still connected.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-4 (ADI1) - E8-9 (SG)
    AUTO switch: ON
    Below 2.5 Ω
    E8-4 (ADI1) - E8-9 (SG)
    OFF switch: ON
    Approx. 329 Ω
    E8-4 (ADI1) - E8-9 (SG)
    TEMP+ switch: ON
    Approx. 1000 Ω
    E8-4 (ADI1) - E8-9 (SG)
    TEMP- switch: ON
    Approx. 3110 Ω



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly.

  1. Disconnect the connector from the steering pad switch assembly.E124484E04

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection (Symbols)
    Condition
    Specified Condition
    z2-3 (AC1) - z2-2 (EAC)
    AUTO switch: ON
    Below 2.5 Ω
    z2-3 (AC1) - z2-2 (EAC)
    OFF switch: ON
    Approx. 329 Ω
    z2-3 (AC1) - z2-2 (EAC)
    TEMP+ switch: ON
    Approx. 1000 Ω
    z2-3 (AC1) - z2-2 (EAC)
    TEMP- switch: ON
    Approx. 3110 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. E144333E13
    Disconnect the connector from the spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D53-10 (AC1) - z2-3 (AC1)
    Center
    Below 1 Ω
    D53-10 (AC1) - z2-3 (AC1)
    2.5 rotations to the left
    Below 1 Ω
    D53-10 (AC1) - z2-3 (AC1)
    2.5 rotations to the right
    Below 1 Ω
    D53-9 (EAC) - z2-2 (EAC)
    Center
    Below 1 Ω
    D53-9 (EAC) - z2-2 (EAC)
    2.5 rotations to the left
    Below 1 Ω
    D53-9 (EAC) - z2-2 (EAC)
    2.5 rotations to the right
    Below 1 Ω

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets below.

    HINT:
    The spiral cable makes a maximum of approximately 5 rotations.



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (A/C CONTROL ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

  1. E153718E03
    Disconnect the connector from the air conditioning control assembly.

  1. Disconnect the connector from the spiral cable sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-4 (ADI1) - D53-10 (AC1)
    Always
    Below 1 Ω
    E8-9 (SG) - D53-9 (EAC)
    Always
    Below 1 Ω
    E8-9 (ADI1) - D53-10 (AC1)
    Always
    10 kΩ or higher
    E8-8 (SG) - D53-9 (EAC)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY (Click here)


← Rear Blower Motor Circuit (from Jul 2010)Steering Pad Switch Circuit (Aug 2008 – Jun 2010) →