2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL WATER PUMP ASSEMBLY

  1. A128115E02
    Install a new water pump gasket and the water pump assembly with the 16 bolts.

    Torque:
    Bolt A:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }
    Bolts B and C:
    9.1 N*m{ 93 kgf*cm , 81 in.*lbf }

    NOTICE:
    1. Make sure that there is no oil on the threads of bolts A.
    2. Be sure to replace 2 bolts C with new ones or reuse them after applying adhesive 1344.

      Adhesive:
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


2. INSTALL WATER INLET HOUSING

  1. A128122
    Install a new water inlet housing gasket and water outlet pipe O-ring.

  1. A133375E04
    Install the water inlet housing with the 2 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful not to allow the O-ring to get caught between the parts.

  1. Connect the water hose.


3. INSTALL WATER PUMP PULLEY

  1. A128112E01
    Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


4. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A161449
    Install the V-ribbed belt tensioner assembly with the 5 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


5. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A162789
    Install the idler pulley cover plate and idler pulley sub-assembly with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


6. INSTALL GENERATOR ASSEMBLY

  1. A170743
    Install the wire harness clamp bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A170150
    Connect the generator bracket with the wire harness clamp.

  1. A170146
    Install generator assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. A170145
    Temporarily install the 2 bolts.

  1. A170145
    Fully tighten the 2bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A170144
    Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 3 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.


7. INSTALL ENGINE HANGERS

  1. A129635E01
    Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 Engine hanger 12281-31120
    No. 2 Engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.


8. REMOVE ENGINE STAND

9. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:
Click here.

← REMOVAL (from Jul 2010)INSTALLATION (Aug 2008 – Jun 2010) →