INSTALLATION
Removal / installation · Vehicles built from Aug 2013
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013
| 1. INSTALL THERMOSTAT |
Install a new gasket to the thermostat.

Install the thermostat with the jiggle valve facing up.
- HINT:
- The jiggle valve may be set within 10° on either side of the prescribed position.
| 2. INSTALL WATER INLET |
Install the water inlet with the 2 nuts .

- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 3. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY |
Install the idler pulley cover plate and idler pulley sub-assembly with the bolt.

- Torque:
- 43 N*m{ 438 kgf*cm , 32 ft.*lbf }
| 4. CONNECT NO. 2 RADIATOR HOSE |
Connect the No. 2 radiator hose to the engine.

| 5. INSTALL V-RIBBED BELT |
Install the V-ribbed belt.

Using SST, turn the V-ribbed belt tensioner assembly counterclockwise and remove the bar.
- SST
- 09961-00950
If it is difficult to install the V-ribbed belt, perform the following procedure:

Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.
Release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and put the V-ribbed belt on the V-ribbed belt tensioner assembly pulley.
- NOTICE:
- Put the backside of the V-ribbed belt on the V-ribbed belt tensioner assembly pulley and No. 2 idler pulley sub-assembly.
- Check that the V-ribbed belt is properly set to each pulley.
- Put the backside of the V-ribbed belt on the V-ribbed belt tensioner assembly pulley and No. 2 idler pulley sub-assembly.
After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the V-ribbed belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.
| 6. INSTALL FRONT FENDER APRON SEAL RH |
Install the front fender apron seal RH with the 2 bolts and clip.

| 7. INSTALL FRONT FENDER LINER RH |
Install the front fender liner RH with the 5 clips and 8 screws.

Install the bolt.
Install 3 new grommets.

Using a 4 mm hexagon wrench, install the 2 screws.
Install the screw and 2 pin hold clips.

Text in Illustration *1
Correct
*2
Incorrect
- NOTICE:
- Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is aligned vertically.
| 8. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH |
- HINT:
- Use the same procedures for the RH side and LH side (Click here).
| 9. INSTALL FRONT WHEEL RH |
- Torque:
- 103 N*m{ 1050 kgf*cm , 76 ft.*lbf }
| 10. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug. (for Bank 1)
- Torque:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf }
Tighten the cylinder block drain cock plug. (for Bank 2, w/ Cylinder Block Drain Cock Plug)
- Torque:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf }
Loosen the air drain cock plug on the water inlet housing.
Loosen the air drain plug at the top of the radiator assembly 3 or 4 turns.

Text in Illustration *1
Air Drain Plug
Add engine coolant to the radiator inlet opening until engine coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug.
- Torque:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf }
Continue to add engine coolant to the radiator inlet opening until engine coolant overflows from the radiator air drain hole. Then tighten the air drain plug.
- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf }
- HINT:
- If the engine coolant level at the radiator inlet opening drops after squeezing the No. 1 radiator hose and No. 2 radiator hose, add engine coolant.
Slowly fill the radiator assembly with engine coolant.
- Standard Capacity:
Condition
Specified Condition
w/ Rear Heater
11.7 liters (12.4 US qts, 10.3 Imp. qts)
w/o Rear Heater
9.5 liters (10.1 US qts, 8.4 Imp. qts)
- NOTICE:
- Never use water as a substitute for engine coolant.
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
Slowly pour engine coolant into the radiator reservoir tank until it reaches the full line.
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
- HINT:
- The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air.
- CAUTION:
- When squeezing the No. 1 radiator hose and No. 2 radiator hose:
- Wear protective gloves.
- Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.
- Keep your hands away from the fan and No. 2 fan.
- Wear protective gloves.
- NOTICE:
- If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
- Make sure that the radiator reservoir tank still has some engine coolant in it.
- If the radiator reservoir tank does not have enough engine coolant, the engine may overheat or be seriously damaged.
- If the radiator reservoir tank does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the radiator reservoir tank is filled to the full line.
- If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reservoir tank.
| 11. INSPECT FOR COOLANT LEAK |
- CAUTION:
- Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
- NOTICE:
- Before performing each inspection, turn the A/C switch off.
Fill the radiator with coolant and attach a radiator cap tester.

Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 12. INSTALL NO. 1 ENGINE UNDER COVER |
Install the No. 1 engine under cover with the 6 bolts and 2 clips.

| 13. INSTALL ENGINE UNDER COVER ASSEMBLY |
Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

Install the engine under cover assembly RR with the 2 bolts.

| 14. INSTALL V-BANK COVER SUB-ASSEMBLY |
Fit the 3 retainers and install the V-bank cover.

