2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Jul 2010 – Jul 2013

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.


2. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


3. REMOVE NO. 1 ENGINE UNDER COVER

  1. A237657
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


4. REMOVE FRONT WHEEL RH

5. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and LH side (Click here).


6. REMOVE FRONT FENDER LINER RH

  1. B258290E01
    Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.

  1. B260030
    Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 3 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.

  1. B260028
    Remove the 5 clips

  1. Remove the bolt, 8 screws and front fender liner RH.


7. REMOVE FRONT FENDER APRON SEAL RH

  1. A171853
    Remove the 2 bolts, clip and front fender apron seal RH.


8. DRAIN ENGINE COOLANT

  1. Loosen the radiator drain cock plug.

    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.


9. REMOVE V-RIBBED BELT

  1. A162386E01
    Using SST, release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and remove the V-ribbed belt from the V-ribbed belt tensioner assembly.
    SST
    09961-00950  

  1. A095070
    While turning the V-ribbed belt tensioner assembly counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner assembly.


10. DISCONNECT NO. 2 RADIATOR HOSE

  1. A162797
    Disconnect the No. 2 radiator hose from the engine.


11. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A162789
    Remove the bolt, idler pulley cover plate and idler pulley sub-assembly.


12. REMOVE WATER INLET

  1. A162796
    Remove the 2 nuts and water inlet.


13. REMOVE THERMOSTAT
  1. Remove the thermostat from the water inlet housing

  1. Remove the gasket from the thermostat.

← REMOVAL (Aug 2008 – Jun 2010)REMOVAL (from Aug 2013) →