2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL FRONT AXLE HUB BEARING

  1. C167714E03
    Using SST and a press, install a new front axle hub bearing to the steering knuckle.
    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07100)


2. INSTALL FRONT DISC BRAKE DUST COVER

  1. C166273
    Install the front disc brake dust cover to the steering knuckle with the 4 bolts.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }


3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY

  1. C167715E03
    Using SST and a press, install the front axle hub sub-assembly to the steering knuckle.
    SST
    09608-32010  
    09950-70010   (09951-07100)
    09950-60010   (09951-00610)


4. INSTALL FRONT AXLE HUB HOLE SNAP RING

  1. C166270
    Using snap ring pliers, install a new front axle hub hole snap ring.


5. INSTALL NO. 1 FRONT WHEEL BEARING DUST DEFLECTOR

  1. C166274E01
    Using SST and a hammer, install a new No. 1 front wheel bearing dust deflector.
    SST
    09316-60011   (09316-00011)
    09608-32010  
    09950-60020   (09951-00810, 09952-06010)
    09950-60010   (09951-00500)

    HINT:
    Align the hole for the speed sensor in the No. 1 front wheel bearing dust deflector with the steering knuckle.


6. INSTALL FRONT LOWER BALL JOINT

  1. C165931
    Install the front lower ball joint to the steering knuckle with the nut.

    Torque:
    123 N*m{ 1254 kgf*cm , 91 ft.*lbf }

    NOTICE:
    Prevent oil from adhering to the screw and tapered parts.

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.


7. INSTALL FRONT AXLE ASSEMBLY

  1. C166269E01
    Install the front axle assembly to the front shock absorber with the 2 bolts and 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }


8. INSTALL FRONT DRIVE SHAFT ASSEMBLY

  1. C165537E05
    Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.


9. INSTALL FRONT LOWER SUSPENSION ARM

  1. C165929
    Install the front lower suspension arm to the front lower ball joint with the bolt and 2 nuts.

    Torque:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }


10. CONNECT TIE ROD ASSEMBLY
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.


11. INSTALL FRONT DISC

  1. C165879E01
    Align the matchmarks and install the front disc.

    NOTICE:
    When replacing the disc with a new one, select the installation position where the front disc has minimal runout.


12. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

  1. C165913
    Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    104 N*m{ 1060 kgf*cm , 76 ft.*lbf }

    NOTICE:
    Do not twist the brake hose when installing the front disc brake caliper assembly.


13. INSTALL FRONT AXLE HUB NUT
  1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.

  1. Using a socket wrench (30 mm), install a new axle hub nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

    HINT:
    1. Keep depressing the brake pedal to prevent the drive shaft from rotating.
    2. Stake the nut after inspecting for looseness and runout in the following steps.


14. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
  1. Remove the 2 bolts and separate the front disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


15. REMOVE FRONT DISC

  1. C165879E01
    Remove the front disc.

    HINT:
    Put matchmarks on the disc and the axle hub.


16. INSPECT FRONT AXLE HUB BEARING LOOSENESS

  1. C166267
    Using a dial indicator, check for looseness near the center of the front axle hub.

    Maximum looseness:
    0 mm (0 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the looseness exceeds the maximum, replace the front axle hub bearing.


17. INSPECT FRONT AXLE HUB RUNOUT

  1. C166268
    Using a dial indicator, check for runout on the surface of the axle hub outside the hub bolt.

    Maximum runout:
    0.05 mm (0.0020 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the runout exceeds the maximum, replace the front axle hub.


18. INSTALL FRONT DISC

  1. C165879E01
    Align the matchmarks and install the front disc.

    NOTICE:
    When replacing the disc with a new one, select the installation position where the front disc has minimal runout.


19. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
  1. Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    104 N*m{ 1060 kgf*cm , 76 ft.*lbf }

    NOTICE:
    Do not twist the brake hose when installing the front disc brake caliper assembly.


20. INSTALL FRONT SPEED SENSOR

  1. C165818E03
    Install the resin clamp and front speed sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from attaching to the sensor tip.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.


21. STAKE FRONT AXLE HUB NUT

  1. C068609E03
    Using a chisel and hammer, stake the front axle hub nut.


22. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


23. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
Inspect and adjust the front wheel alignment (Click here).


24. CHECK FOR SPEED SENSOR SIGNAL

HINT:
Check for speed sensor signals (Click here).

← REMOVAL (from Jul 2010)INSTALLATION (Aug 2008 – Jun 2010) →