B2272 Ignition 1 Monitor Malfunction
Diagnostic trouble codes · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
This DTC is output if there is a problem in the IG1D output circuit, which is from the inside of the main body ECU to the IG1 relay.- HINT:
- If the main body ECU is replaced with a new one while the negative (-) battery terminal is connected, the power source mode will be in IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
- After the main body ECU is replaced, perform the registration procedure for the engine immobiliser system.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2272 |
IG1 relay actuation circuit inside main body ECU or other related circuit is malfunctioning |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the intelligent tester main switch on.
Select the item below in the Data List, and read the display on the tester.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
IG1 Relay Mon1
Status of IG1 relay monitor (outer) / ON or OFF
ON: Engine switch on (IG) (IG1 relay is ON)
OFF: Engine switch off (IG1 relay is OFF)
-
- OK:
- "ON" (engine switch on (IG)) appears on the screen.
|
|
||||
| OK | |
| 2. CHECK ENGINE SWITCH CONDITION |
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:
- OK:
- off → on (ACC) → on (IG) → off
|
|
||||
| OK | |
| 3. CHECK DTC OUTPUT |
Delete the DTCs (Click here).
Check for DTCs again.
- OK:
- No DTC is output.
|
|
||||
| OK | ||
| ||
| 4. INSPECT RELAY (IG1 RELAY) |
Remove the IG1 relay from the instrument panel junction block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - MAIN BODY ECU) |
Disconnect the 1I junction block connector.


Disconnect the D7 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1I-9 - D7-3 (IG1D)
Always
Below 1 Ω
D7-3 (IG1D) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY AND BODY GROUND) |
Disconnect the 1F and 1A junction block connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1F-10 - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
1A-1 - Body ground
Always
11 to 14 V
|
|
||||
| OK | ||
| ||
