2007-2013 Highlander Kluger · Service Manual ENGINE

B2272 Ignition 1 Monitor Malfunction

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This DTC is output if there is a problem in the IG1D output circuit, which is from the inside of the main body ECU to the IG1 relay.

HINT:
If the main body ECU is replaced with a new one while the negative (-) battery terminal is connected, the power source mode will be in IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU is replaced, perform the registration procedure for the engine immobiliser system.

DTC No.
DTC Detection Condition
Trouble Area
B2272
IG1 relay actuation circuit inside main body ECU or other related circuit is malfunctioning
  1. Main body ECU (Instrument panel junction block)
  2. IG1 relay
  3. Wire harness or connector

WIRING DIAGRAM

B176779E04

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the intelligent tester main switch on.

  1. Select the item below in the Data List, and read the display on the tester.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG1 Relay Mon1
    Status of IG1 relay monitor (outer) / ON or OFF
    ON: Engine switch on (IG) (IG1 relay is ON)
    OFF: Engine switch off (IG1 relay is OFF)
    -

    OK:
    "ON" (engine switch on (IG)) appears on the screen.



NG
Go to step 4
OK


2. CHECK ENGINE SWITCH CONDITION
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:

      OK:
      off → on (ACC) → on (IG) → off



NG
GO TO OTHER FLOW CHART (Click here)
OK


3. CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

  1. Check for DTCs again.

    OK:
    No DTC is output.



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK

USE SYMPTOM METHOD TO CHECK (Click here)

4. INSPECT RELAY (IG1 RELAY)

  1. A092673E45
    Remove the IG1 relay from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE IG1 RELAY
OK


5. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - MAIN BODY ECU)

  1. Disconnect the 1I junction block connector.B138001E35

  1. Disconnect the D7 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1I-9 - D7-3 (IG1D)
    Always
    Below 1 Ω
    D7-3 (IG1D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - MAIN BODY ECU)
OK


6. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY AND BODY GROUND)

  1. B175599E02
    Disconnect the 1F and 1A junction block connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1F-10 - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1A-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY AND BODY GROUND)
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← B2271 Ignition Hold Monitor Malfunction (from Jul 2010)B2272 Ignition 1 Monitor Malfunction (Aug 2008 – Jun 2010) →