VC Output Circuit
Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
- HINT:
- Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to the on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch on (IG).
- OK:
- MIL lights up.
|
|
||||
| OK | ||
| ||
| 2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Check the communication between the tester and ECM.
- Result:
Result
Proceed to
Communication is possible
A
Communication is not possible
B
|
|
||||
| B | |
| 3. CHECK THROTTLE BODY (CHECK MIL ILLUMINATED) |
Disconnect the throttle body connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the throttle body connector.
|
|
||||
| B | |
| 4. CHECK ACCELERATOR PEDAL ROD (CHECK MIL ILLUMINATED) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the accelerator pedal position sensor connector.
|
|
||||
| B | |
| 5. CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED) |
Disconnect the VVT sensor for intake camshaft bank 1 connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor for intake camshaft bank 1 connector.
|
|
||||
| B | |
| 6. CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 1 (CHECK MIL ILLUMINATED) |
Disconnect the VVT sensor for exhaust camshaft bank 1 connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor for exhaust camshaft bank 1 connector.
|
|
||||
| B | |
| 7. CHECK VVT SENSOR FOR INTAKE CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED) |
Disconnect the VVT sensor for intake camshaft bank 2 connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor for intake camshaft bank 2 connector.
|
|
||||
| B | |
| 8. CHECK VVT SENSOR FOR EXHAUST CAMSHAFT BANK 2 (CHECK MIL ILLUMINATED) |
Disconnect the VVT sensor for exhaust camshaft bank 2 connector.
Turn the ignition switch on (IG).
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor for exhaust camshaft bank 2 connector.
|
|
||||
| B | |
| 9. CHECK HARNESS AND CONNECTOR |
Disconnect the throttle body connector.

Disconnect the accelerator pedal position sensor connector.
Disconnect the VVT sensor for intake camshaft bank 1 connector.
Disconnect the VVT sensor for exhaust camshaft bank 1 connector.
Disconnect the VVT sensor for intake camshaft bank 2 connector.
Disconnect the VVT sensor for exhaust camshaft bank 2 connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
VC (B1-23) - Body ground
10 kΩ or higher
VCPA (D31-26) - Body ground
10 kΩ or higher
VCP2 (D31-27) - Body ground
10 kΩ or higher
Reconnect the ECM connectors.
Reconnect the VVT sensor for exhaust camshaft bank 2 connector.
Reconnect the VVT sensor for intake camshaft bank 2 connector.
Reconnect the VVT sensor for exhaust camshaft bank 1 connector.
Reconnect the VVT sensor for intake camshaft bank 1 connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the throttle body connector.
|
|
||||
| OK | ||
| ||
