2007-2013 Highlander Kluger · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A207756E24
When the VC circuit is shorted, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A204202E05
A243400E01

INSPECTION PROCEDURE


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) illuminates when turning the ignition switch on (IG).

    OK:
    MIL illuminates.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Check the communication between the tester and ECM.

    Result:
    Result
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the throttle position sensor connector.



B
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
A


4. CHECK MIL (ACCELERATOR PEDAL ASSEMBLY)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the accelerator pedal sensor assembly connector.



B
REPLACE ACCELERATOR PEDAL ASSEMBLY (Click here)
A


5. CHECK MIL (VVT SENSOR FOR INTAKE SIDE BANK 1)
  1. Disconnect the VVT sensor for intake side bank 1 connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the VVT sensor for intake side bank 1 connector.



B
REPLACE VVT SENSOR FOR INTAKE SIDE BANK 1 (Click here)
A


6. CHECK MIL (VVT SENSOR FOR INTAKE SIDE BANK 2)
  1. Disconnect the VVT sensor for intake side bank 2 connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the VVT sensor for intake side bank 2 connector.



B
REPLACE VVT SENSOR FOR INTAKE SIDE BANK 2 (Click here)
A


7. CHECK MIL (VVT SENSOR FOR EXHAUST SIDE BANK 1)
  1. Disconnect the VVT sensor for exhaust side bank 1 connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the VVT sensor for exhaust side bank 1 connector.



B
REPLACE VVT SENSOR FOR EXHAUST SIDE BANK 1 (Click here)
A


8. CHECK MIL (VVT SENSOR FOR EXHAUST SIDE BANK 2)
  1. Disconnect the VVT sensor for exhaust side bank 2 connector.

  1. Turn the ignition switch on (IG).

  1. Check the MIL.

    Result:
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the VVT sensor for exhaust side bank 2 connector.



B
REPLACE VVT SENSOR FOR EXHAUST SIDE BANK 2 (Click here)
A


9. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B48-13 (VCTA) or B27-5 (VC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE POSITION SENSOR - ECM)
OK


10. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D55-2 (VCP2) or A19-1 (VCP2) - Body ground
    Always
    10 kΩ or higher
    D55-4 (VCPA) or A19-4 (VCPA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the accelerator pedal sensor assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
OK


11. CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE SIDE BANK 2 - ECM)
  1. Disconnect the VVT sensor for intake side bank 2 connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B50-16 (VCV2) or B23-3 (VC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor for intake side bank 2 connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR FOR INTAKE SIDE BANK 2 - ECM)
OK


12. CHECK HARNESS AND CONNECTOR (VCV1 CIRCUIT)
  1. Disconnect the VVT sensor for intake side bank 1 connector.

  1. Disconnect the VVT sensor for exhaust side bank 1 connector.

  1. Disconnect the VVT sensor for exhaust side bank 2 connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B50-15 (VCV1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor for exhaust side bank 2 connector.

  1. Reconnect the VVT sensor for exhaust side bank 1 connector.

  1. Reconnect the VVT sensor for intake side bank 1 connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← VC Output Circuit (Aug 2008 – Jun 2010)Fuel Pump Control Circuit (May 2007 – Jul 2008) →