2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

B1242 Wireless Door Lock Tuner Circuit Malfunction

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU.
DTC No.
DTC Detection Condition
Trouble Area
B1242
In diagnostic mode, an applicable RDA signal cannot be received within 1 second after a PRG signal has been output from the main body ECU.
  1. Wire harness or connector
  2. Door control receiver
  3. Main body ECU

WIRING DIAGRAM

B176380E03

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)

  1. for LHD:

    1. Disconnect the D6 main body ECU connector and the O28 door control receiver connector.B175272E02

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D6-12 (RDA) - O28-2 (RDA)
      Always
      Below 1 Ω
      D6-12 (RDA) - Body ground
      Always
      10 kΩ or higher
      D6-10 (PRG) - O28-3 (PRG)
      Always
      Below 1 Ω
      D6-10 (PRG) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the D6 main body ECU connector and the O38 door control receiver connector.B176374E01

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D6-12 (RDA) - O38-2 (RDA)
      Always
      Below 1 Ω
      D6-12 (RDA) - Body ground
      Always
      10 kΩ or higher
      D6-10 (PRG) - O38-3 (PRG)
      Always
      Below 1 Ω
      D6-10 (PRG) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (BATTERY, BODY GROUND)

  1. for LHD:

    1. B176375E01
      Measure the voltage and resistance according to the value(s) in the table below.

      Standard:
      Tester Connection
      Condition
      Specified Condition
      O28-1 (GND) - Body ground
      Always
      Below 1 Ω
      O28-5 (+B) - Body ground
      Always
      11 to 14 V

  1. for RHD:

    1. B176376E01
      Measure the voltage and resistance according to the value(s) in the table below.

      Standard:
      Tester Connection
      Condition
      Specified Condition
      O38-1 (GND) - Body ground
      Always
      Below 1 Ω
      O38-5 (+B) - Body ground
      Always
      11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE DOOR CONTROL RECEIVER
  1. Reconnect the D6 main body ECU connector.

  1. Replace the door control receiver with a normal one (Click here).

  1. Perform the registration procedures (Click here).

    HINT:
    If a normally functioning door control receiver is available, connect it and check if the wireless door lock function is normal or DTCs are output. If the alternative receiver functions normally, replace the original door control receiver.


NEXT


4. CONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check if the same DTC is detected.

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result:
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← B1242 Wireless Door Lock Tuner Circuit Malfunction (May 2007 – Jul 2008)B1242 Wireless Door Lock Tuner Circuit Malfunction (from Jul 2010) →