2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010

DESCRIPTION

The driver side seat belt buckle switch circuit consists of the center airbag sensor assembly and the front seat inner belt assembly (Driver side).
DTC B1655/37 is recorded when a malfunction is detected in the driver side seat belt buckle switch circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1655/37
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the driver side seat belt buckle switch circuit for 2 seconds.
  2. Front seat inner belt assembly (Driver side) malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Front seat inner belt assembly (Driver side seat belt buckle switch)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C170112E01

INSPECTION PROCEDURE


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and front seat inner belt assembly (Driver side).

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly (Driver side).

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


2. CHECK WIRE HARNESS (OPEN)

  1. Using SST, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.C157711E02

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-1 (LBE+) - O10-3 (LBE-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-1 (RBE+) - N19-3 (RBE-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


3. CHECK WIRE HARNESS (SHORT)

  1. C169654E01
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-1 (LBE+) - O10-3 (LBE-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-1 (RBE+) - N19-3 (RBE-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


4. CHECK WIRE HARNESS (SHORT TO B+)

  1. C169654E01
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-1 (LBE+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O10-3 (LBE-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-1 (RBE+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N19-3 (RBE-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


5. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C169654E01
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-1 (LBE+) - Body ground
    Always
    1 MΩ or higher
    O10-3 (LBE-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-1 (RBE+) - Body ground
    Always
    1 MΩ or higher
    N19-3 (RBE-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


6. CHECK FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)

  1. C167899E02
    Connect the connectors to the center airbag sensor assembly and the front seat inner belt assembly (Driver side).

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)

7. REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly (Driver side) (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


8. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C167899E03
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END


← B1653/35 Seat Position Airbag Sensor Circuit Malfunction (from Jul 2010)B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (Aug 2008 – Jun 2010) →