2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1655/37 Seat Belt Buckle Switch RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2010

DESCRIPTION

The seat belt buckle switch RH circuit consists of the center airbag sensor assembly and front seat inner belt assembly RH.
DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch RH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1655/37
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch RH circuit.
  2. Front seat inner belt assembly RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat inner belt assembly RH (Seat belt buckle switch RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C171040E23

INSPECTION PROCEDURE


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and front seat inner belt assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and front seat inner belt assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


2. CHECK FLOOR WIRE (OPEN)

  1. Using SST, connect terminals 15 (RBE+) and 14 (RBE-) of connector B.C227343E01

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N19-1 (RBE+) - N19-3 (RBE-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


3. CHECK FLOOR WIRE (SHORT)

  1. C227344E01
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N19-1 (RBE+) - N19-3 (RBE-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (SHORT TO B+)

  1. C227344E01
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-1 (RBE+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N19-3 (RBE-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C227344E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N19-1 (RBE+) - Body ground
    Always
    1 MΩ or higher
    N19-3 (RBE-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


6. CHECK FRONT SEAT INNER BELT ASSEMBLY RH

  1. C166177E11
    Connect the connectors to the center airbag sensor assembly and front seat inner belt assembly RH.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)

7. REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly RH with a known good part (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.


NEXT


8. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C166177E11
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655/37 is not output.

    HINT:
    Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END


← B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (Aug 2008 – Jun 2010)B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction (from Jul 2010) →