2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2010

DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and front seat inner belt assembly LH.
DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1656/38
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit.
  2. Front seat inner belt assembly LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C171040E24

INSPECTION PROCEDURE


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and front seat inner belt assembly LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and front seat inner belt assembly LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


2. CHECK NO. 2 FLOOR WIRE (OPEN)

  1. Using SST, connect terminals 11 (LBE+) and 12 (LBE-) of connector B.C171045E16

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O10-1 (LBE+) - O10-3 (LBE-)
    Always
    Below 1 Ω



NG
REPLACE NO. 2 FLOOR WIRE
OK


3. CHECK NO. 2 FLOOR WIRE (SHORT)

  1. C171046E13
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O10-1 (LBE+) - O10-3 (LBE-)
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

  1. C171046E13
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-1 (LBE+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O10-3 (LBE-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE NO. 2 FLOOR WIRE
OK


5. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

  1. C171046E13
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O10-1 (LBE+) - Body ground
    Always
    1 MΩ or higher
    O10-3 (LBE-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


6. CHECK FRONT SEAT INNER BELT ASSEMBLY LH

  1. C166120E07
    Connect the connectors to the center airbag sensor assembly and front seat inner belt assembly LH.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656/38 is not output.

    HINT:
    Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)

7. REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt assembly LH with a known good part (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.


NEXT


8. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C166120E07
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656/38 is not output.

    HINT:
    Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END


← B1655/37 Seat Belt Buckle Switch RH Circuit Malfunction (from Jul 2010)B1800/51 Short in Driver Side Squib Circuit (+ B1801/51, B1802/51, B1803/51) (May 2007 – Jul 2008) →