2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010

DESCRIPTION

The front passenger side pretensioner squib circuit consists of the center airbag sensor assembly and the front seat outer belt assembly (Passenger side).
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side pretensioner squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1905/74
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the front passenger side pretensioner squib circuit during primary check.
  2. Front passenger side pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Front seat outer belt assembly (Front passenger side pretensioner squib)
  4. Center airbag sensor assembly
B1906/74
  1. The center airbag sensor assembly receives an open circuit signal in the front passenger side pretensioner squib circuit for 2 seconds.
  2. Front passenger side pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Front seat outer belt assembly (Front passenger side pretensioner squib)
  4. Center airbag sensor assembly
B1907/74
  1. The center airbag sensor assembly receives a short circuit to ground signal in the front passenger side pretensioner squib circuit for 0.5 seconds.
  2. Front passenger side pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Front seat outer belt assembly (Front passenger side pretensioner squib)
  4. Center airbag sensor assembly
B1908/74
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the front passenger side pretensioner squib circuit for 0.5 seconds.
  2. Front passenger side pretensioner squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Front seat outer belt assembly (Front passenger side pretensioner squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C169773E07

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTORS

  1. C165140E03
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the front seat outer belt assembly (Passenger side) and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the front seat outer belt assembly (Passenger side) and center airbag sensor assembly.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the wire harness connector (on the front seat outer belt assembly (Passenger side)) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


2. CHECK FRONT SEAT OUTER BELT ASSEMBLY (FRONT PASSENGER SIDE PRETENSIONER SQUIB)

  1. C168804E02
    Connect the connector to the center airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt assembly (Front passenger side pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907, B1908, or 74 is not output.

    HINT:
    Codes other than DTC B1905, B1906, B1907, B1908, and 74 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY (PASSENGER SIDE) (Click here)

3. CHECK WIRE HARNESS (FRONT PASSENGER SIDE PRETENSIONER SQUIB CIRCUIT)

  1. C157583E05
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      N4-1 (R+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      N4-2 (R-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      O4-2 (L-) - Body ground
      Ignition switch on (IG)
      Below 1 V

      Result:
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      N4-1 (R+) - N4-2 (R-)
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - O4-2 (L-)
      Always
      Below 1 Ω

      Result:
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      N4-1 (R+) - Body ground
      Always
      1 MΩ or higher
      N4-2 (R-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - Body ground
      Always
      1 MΩ or higher
      O4-2 (L-) - Body ground
      Always
      1 MΩ or higher

      Result:
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      N4-1 (R+) - N4-2 (R-)
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - O4-2 (L-)
      Always
      1 MΩ or higher

      Result:
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


4. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C168805E01
    Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front seat outer belt assembly (Passenger side) and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907, B1908, or 74 is not output.

    HINT:
    Codes other than DTC B1905, B1906, B1907, B1908, or 74 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1905/74 Short in Front Pretensioner Squib LH Circuit (+ B1906/74, B1907/74, B1908/74) (from Jul 2010)B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit (+ B1906/74, B1907/74, B1908/74) (Aug 2008 – Jun 2010) →