2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1905/74 Short in Front Pretensioner Squib LH Circuit

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor assembly and front seat outer belt assembly LH.
The center airbag sensor assembly uses this circuit to deploy the seat belt pretensioner when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1905/74
  1. The center airbag sensor assembly receives a line short circuit signal in the front pretensioner squib LH circuit during primary check.
  2. Front pretensioner squib LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Center airbag sensor assembly
B1906/74
  1. The center airbag sensor assembly receives an open circuit signal in the front pretensioner squib LH circuit.
  2. Front pretensioner squib LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Center airbag sensor assembly
B1907/74
  1. The center airbag sensor assembly receives a short circuit to ground signal in the front pretensioner squib LH circuit.
  2. Front pretensioner squib LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Center airbag sensor assembly
B1908/74
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the front pretensioner squib LH circuit.
  2. Front pretensioner squib LH malfunction
  3. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C198980E59

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTORS

  1. C165141E41
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the front seat outer belt assembly LH and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the front seat outer belt assembly LH and center airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the No. 2 floor wire connector (on the front seat outer belt assembly LH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

  1. Check that the short spring for the No. 2 floor wire with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


2. CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)

  1. C213511E06
    Connect the connector to the center airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to pretensioner deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907, B1908 or 74 is not output.

    HINT:
    Codes other than DTCs B1905, B1906, B1907, B1908 and 74 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (Click here)

3. CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)

  1. C157584E09
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Disconnect the No. 2 floor wire from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      O4-1 (L+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      O4-2 (L-) - Body ground
      Ignition switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O4-1 (L+) - O4-2 (L-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O4-1 (L+) - Body ground
      Always
      1 MΩ or higher
      O4-2 (L-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O4-1 (L+) - O4-2 (L-)
      Always
      1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C170972E06
    Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front seat outer belt assembly LH and center airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907, B1908 or 74 is not output.

    HINT:
    Codes other than DTCs B1905, B1906, B1907, B1908 and 74 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (Aug 2008 – Jun 2010)B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit (+ B1906/74, B1907/74, B1908/74) (May 2007 – Jul 2008) →