2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. REMOVE FRONT WHEEL RH

2. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


3. REMOVE NO. 1 ENGINE UNDER COVER

  1. A171855
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


4. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and LH side (Click here).


5. REMOVE FRONT FENDER LINER RH

  1. B174753E01
    Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

  1. B174750
    Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.

  1. B174752
    Remove the 5 clips, 7 screws and front fender liner RH.


6. REMOVE FRONT FENDER APRON SEAL RH

  1. A171853
    Remove the 2 bolts, clip and front fender apron seal RH.


7. DRAIN ENGINE COOLANT

  1. Loosen the radiator drain cock plug.

    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.


8. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.


9. REMOVE COOL AIR INTAKE DUCT SEAL

  1. A170196
    Remove the 11 clips and cool air intake duct seal.


10. REMOVE BATTERY

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. A175880
    Loosen the nut, and disconnect the negative battery terminal.

  1. Loosen the nut, and disconnect the positive battery terminal.

  1. Loosen the nut, and remove the bolt and battery clamp.

  1. Remove the battery and battery tray.


11. REMOVE NO. 2 AIR CLEANER INLET

  1. A170453
    Disconnect the 2 vacuum switching valve clamps.

  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolts and No. 2 air cleaner inlet.


12. REMOVE NO. 1 AIR CLEANER INLET

  1. A170454
    Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.


13. DISCONNECT NO. 1 RADIATOR HOSE

  1. A169427
    Disconnect the No. 1 radiator hose from the radiator.


14. DISCONNECT NO. 2 RADIATOR HOSE

  1. A169428
    Disconnect the No. 2 radiator hose from the radiator.


15. DISCONNECT OIL COOLER HOSE

  1. A169429
    Disconnect the oil cooler hoses from the radiator.


16. DISCONNECT COOLING FAN ECU CONNECTOR

  1. A169435
    Detach the wire harness clamps from the fan shroud LH side.

  1. A169436
    Detach the wire harness clamps from the fan shroud RH side and disconnect the cooling fan ECU connector.


17. REMOVE RADIATOR GRILLE

  1. B172749E01
    Put protective tape around the radiator grille.

  1. B172746
    Remove the 2 bolts and 4 clips.

  1. B172747
    Disengage the 6 claws and 4 guides, and remove the radiator grille.


18. REMOVE HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)

  1. B174188
    Remove the hood lock nut cap.

  1. B174189
    Remove the 3 bolts.

  1. B174190
    Disconnect the hood lock control cable and remove the hood lock assembly.


19. REMOVE HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)

  1. B174191
    Disconnect the connector.

  1. B174192
    Remove the hood lock nut cap.

  1. B174193
    Remove the 3 bolts.

  1. B174194
    Disconnect the hood lock control cable and remove the hood lock assembly.


20. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for LHD)

  1. A169432
    Disconnect the low pitched horn and high pitched horn connectors.

  1. A169469
    Detach the hood lock control cable clamp and remove the 6 bolts and upper radiator support sub-assembly.


21. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for RHD)

  1. A169432
    Disconnect the low pitched horn and high pitched horn connectors.

  1. A169470
    Detach the hood lock control cable clamp and remove the 6 bolts and upper radiator support sub-assembly.


22. SEPARATE COOLER CONDENSER ASSEMBLY

  1. A169439
    Remove the 4 bolts and move the cooler condenser assembly to remove the radiator assembly and fan assembly with motor.


23. REMOVE RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR

  1. A169440
    Remove the radiator assembly and fan assembly with motor.


24. REMOVE NO. 2 OIL LEVEL DIPSTICK GUIDE

  1. A170143
    Remove the bolt and the No. 2 oil level dipstick guide.


25. REMOVE V-RIBBED BELT

  1. A162386E01
    Using SST, release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and remove the V-ribbed belt from the V-ribbed belt tensioner assembly.
    SST
    09961-00950  

  1. A095070
    While turning the V-ribbed belt tensioner assembly counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner assembly.


26. REMOVE GENERATOR ASSEMBLY

  1. A170144
    Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.

  1. Disconnect the connector from the compressor and magnetic clutch.

  1. Disconnect the 3 wire harness clamps.

  1. A170145
    Remove the 2 bolts, and then disconnect the bracket.

  1. A170146
    Remove the 2 bolts and the generator assembly.

  1. A170150
    Disconnect the wire harness clamp, and then remove the generator bracket.

  1. A170743
    Remove the bolt and the wire harness clamp bracket.

← REMOVAL (May 2007 – Jul 2008)REMOVAL (Jul 2010 – Jul 2013) →