2007-2013 Highlander Kluger · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from May 2007


1. REMOVE TRANSFER COVER GASKET

  1. C082798
    Remove the transfer cover gasket from the transfer assembly.


2. REMOVE TRANSFER CASE BREATHER PLUG

  1. C094714
    Using a screwdriver and a hammer, remove the transfer case breather plug from the No. 1 transfer case cover.

    NOTICE:
    Be careful not to damage the contact surface of the No. 1 transfer case cover.


3. REMOVE NO. 1 TRANSFER CASE COVER

  1. C083507
    Remove the 8 bolts.

  1. C050303
    Using a brass bar and a hammer, remove the No. 1 transfer case cover from the transfer case.

    NOTICE:
    Be careful not to damage the contact surfaces of the case and cover.


4. REMOVE BREATHER OIL DEFLECTOR

  1. C067665
    Remove the bolt and breather oil deflector from the No. 1 transfer case cover.


5. REMOVE TRANSFER DYNAMIC DAMPER

  1. C082802
    Remove the 3 bolts and the transfer dynamic damper from the transfer extension housing sub-assembly.


6. REMOVE TRANSFER CASE STRAIGHT PIN
  1. Remove the 4 transfer case straight pins from the transfer case.


7. REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT
  1. Remove the 4 transfer and transaxle setting stud bolts.


8. FIX TRANSFER ASSEMBLY
  1. Fix the transfer assembly to the overhaul attachment.


9. REMOVE TRANSFER EXTENSION HOUSING DUST DEFLECTOR

  1. C082788
    Using a plastic hammer, remove the transfer extension housing dust deflector from the transfer extension housing sub-assembly.


10. REMOVE TRANSFER EXTENSION HOUSING TYPE T OIL SEAL

  1. C082978E02
    Using SST, remove the transfer extension housing type T oil seal from the transfer extension housing.
    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil-seal-fitted surface of the housing and the inside surface of the bush.


11. REMOVE TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

  1. C082790
    Remove the 4 bolts.

  1. C082791
    Using a plastic hammer, remove the transfer extension housing sub-assembly from the transfer case.


12. INSPECT PRELOAD

  1. C083635E10
    Using SST and a torque wrench, check the initial torque with the backlash range.
    SST
    09326-20011  

    Torque:
    0.9 to 1.4 N*m{ 9 to 14 kgf*cm , 8.0 to 12.4 in.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 160 mm (6.30 in.).

  1. Using SST and a torque wrench, check the initial torque while the driven pinion is in contact with the ring gear face.

    SST
    09326-20011  

    Torque:
    Preload:
    1.07 to 1.68 N*m{ 10.9 to 17.1 kgf*cm , 9.5 to 14.9 in.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 160 mm (6.30 in.).


13. REMOVE CENTER DIFFERENTIAL LOCK SLEEVE

  1. C083637
    Using snap ring pliers, remove the shaft snap ring.

  1. C083638E02
    Using SST, remove the CTR differential lock sleeve.
    SST
    09308-00010  


14. REMOVE O-RING

  1. C050311
    Using a screwdriver with the tip protected by vinyl tape, remove the O-ring from the CTR differential lock sleeve.

    NOTICE:
    Be careful not to damage the lock sleeve's groove for the O-ring.


15. REMOVE TRANSFER CASE OIL SEAL

  1. C083630E03
    Using SST, remove the transfer case oil seal from the case.
    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil-seal-fitted surface of the case.


16. REMOVE TRANSFER RH BEARING RETAINER OIL SEAL

  1. C082980E02
    Using SST, remove the transfer RH bearing retainer oil seal from the transfer RH bearing retainer sub-assembly.
    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil-seal-fitted surface of the retainer.


17. REMOVE TRANSFER RH BEARING RETAINER SUB-ASSEMBLY

  1. C083509
    Remove the 7 bolts from the transfer RH bearing retainer sub-assembly.

  1. C149592E01
    Using SST, make a clearance between the transfer RH bearing retainer sub-assembly and the transfer case.
    SST
    09950-00020  

  1. Remove SST.

  1. C082981E06
    Using SST, remove the transfer RH bearing retainer sub-assembly from the transfer case.
    SST
    09520-10021  


18. REMOVE O-RING

  1. C050313
    Using a screwdriver with the tip protected by vinyl tape, remove the 2 O-rings from the transfer RH bearing retainer sub-assembly.

    NOTICE:
    Be careful not to damage the retainer's grooves for the O-rings.


19. REMOVE CENTER DIFFERENTIAL CASE TAPERED ROLLER BEARING

  1. C083639E02
    Fix the transfer RH bearing retainer sub-assembly in a vise.

  1. Using SST, remove the center differential case tapered roller bearing RH outer race, No. 2 transfer ring gear mounting case washer and No. 2 transfer RH bearing retainer oil seal from the transfer RH bearing retainer sub-assembly.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the oil-seal-fitted surface of the transfer RH bearing retainer sub-assembly.


20. REMOVE SIDE GEAR SHAFT HOLDER BEARING

  1. C083640
    Using snap ring pliers, remove the side gear shaft holder hole snap ring.

  1. Remove the side gear shaft holder bearing from the transfer RH bearing retainer sub-assembly.


21. REMOVE TRANSFER RING GEAR MOUNTING CASE

  1. C067673
    Remove the transfer ring gear mounting case from the transfer case.


22. REMOVE CENTER DIFFERENTIAL CASE TAPERED ROLLER BEARING
SST
09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010   (09951-00430)

  1. C083641E02
    Using SST, remove the inner race of the center differential case tapered roller bearing from the transfer ring gear mounting case.

    NOTICE:
    Apply grease to the screw thread and tip of SST before use.

  1. C083642E02
    When the roller comes off due to deformation of the gauge, completely remove the roller and remaining inner races of the center differential case tapered roller bearing from the transfer ring gear mounting case.
    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00430)

    NOTICE:
    Apply grease to the screw thread and tip of SST before use.

  1. C083643E02
    Using SST, remove the inner race of the center differential case tapered roller bearing from the transfer ring gear mounting case.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)

    NOTICE:
    Apply grease to the screw thread and tip of SST before use.

  1. C083644E02
    When the roller comes off due to deformation of the gauge, completely remove the roller and remaining inner races of the center differential case tapered roller bearing from the transfer ring gear mounting case.
    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00360)

    NOTICE:
    Apply grease to the screw thread and tip of SST before use.


23. REMOVE RING GEAR

  1. C083645E03
    Put matchmarks on the transfer ring gear mounting case and the ring gear.

  1. Remove the 12 bolts.

  1. C067677
    Using a plastic hammer, remove the ring gear by tapping around its periphery.

    NOTICE:
    Do not damage the teeth of the ring gear.


24. REMOVE TRANSFER GEAR NUT

  1. C082795E02
    Using SST and a hammer, unstake the transfer gear nut.
    SST
    09930-00010  

  1. C082984E02
    Using SST, remove the transfer gear nut.
    SST
    09326-20011  
    09556-16030  

  1. C082796
    Using a press, remove the driven pinion, transfer driven pinion rear bearing inner race and transfer pinion bearing spacer.

    NOTICE:
    1. Put shop cloths around the transfer case to help prevent the driven pinion from dropping out of the bearing.
    2. Place something like wooden blocks under the case to keep its level.


25. REMOVE TRANSFER DRIVEN PINION FRONT BEARING

  1. C083646E02
    Using SST and a press, remove the transfer driven pinion front bearing inner race from the driven pinion.
    SST
    09950-00020  


26. REMOVE CENTER DIFFERENTIAL CASE TAPERED ROLLER BEARING

  1. C050329
    Using a brass bar and a hammer, lightly strike the center differential case tapered roller bearing LH outer race at 2 positions to remove it from the transfer case.


27. REMOVE TRANSFER OUTPUT SHAFT WASHER
  1. Remove the ring gear mounting case plate washer from the transfer case.


28. REMOVE CENTER DIFFERENTIAL CASE TAPERED ROLLER BEARING

  1. C082781
    Using a brass bar and a hammer, lightly strike the transfer driven pinion front bearing outer race at 2 points to remove it from the transfer case.


29. REMOVE RING GEAR MOUNTING CASE PLATE WASHER
  1. Remove the transfer output washer from the transfer case.


30. REMOVE TRANSFER DRIVEN PINION REAR BEARING

  1. C050331
    Using a brass bar and a hammer, lightly strike the transfer driven pinion rear bearing outer race at 2 points to remove it from the transfer case.

← REMOVAL (from Aug 2013)INSPECTION (from May 2007) →