2007-2013 Highlander Kluger · Service Manual DRIVE LINE

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE REAR WHEEL

2. REMOVE REAR DIFFERENTIAL FILLER PLUG

  1. C166706
    Using a hexagon wrench (10 mm), remove the rear differential filler plug and rear differential filler plug gasket.


3. REMOVE REAR DIFFERENTIAL DRAIN PLUG

  1. C166707
    Using a hexagon wrench (10 mm), remove the rear differential drain plug and rear differential drain plug gasket, and drain the oil.


4. SEPARATE REAR SPEED SENSOR

  1. C165809
    Remove the bolt and separate the rear speed sensor from the rear axle carrier sub-assembly.

    NOTICE:
    Keep the sensor tip and rear speed sensor installation hole free from foreign matter.


5. REMOVE REAR AXLE SHAFT NUT

  1. C165539E01
    Using SST and a hammer, release the staked part of the rear axle shaft nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the rear axle shaft nut.


6. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

  1. C165996
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


7. REMOVE REAR DISC

  1. C166438E01
    Put matchmarks on the rear disc and the axle hub.

  1. D028126
    Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.


8. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

  1. C166348E01
    Put matchmarks on the drive shaft and axle hub.

    NOTICE:
    Do not punch the marks.

  1. C165997
    Remove the 4 bolts and the rear axle hub and bearing assembly.

    NOTICE:
    1. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.
    2. Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable assembly.


9. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C166156
    Remove the 2 bolts and separate the No. 3 parking brake cable assembly from the backing plate.

  1. Remove the 2 bolts, 4 nuts, and the No. 3 parking brake cable assembly.

    C166164


10. REMOVE REAR STRUT ROD ASSEMBLY

  1. C165999
    Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.


11. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

  1. C166000
    Loosen the 2 bolts.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.

  1. C166001
    Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring (lower side) from the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.

  1. C166002
    Remove the 2 bolts, the 2 nuts, and the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.

    HINT:
    Use wire or an equivalent tool to keep the rear drive shaft assembly from hanging down.


12. REMOVE NO. 2 REAR SUSPENSION ARM ASSEMBLY

C166222E01
  1. Put matchmarks on the adjust cams and the rear suspension member sub-assembly.

  1. Remove the nut, the No. 2 camber adjust cam, the rear suspension toe adjust cam sub-assembly, and the rear No. 2 suspension arm assembly LH.

    NOTICE:
    Mark the removed parts to distinguish left from right and keep them in order for reinstallation.

    HINT:
    When removing the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.


13. REMOVE NO. 1 REAR SUSPENSION ARM ASSEMBLY

C166220
  1. Remove the bolt, the nut, and the rear No. 1 suspension arm assembly LH from the rear suspension member sub-assembly.

    NOTICE:
    Since a stopper nut is used, loosen the bolt.


14. REMOVE REAR DRIVE SHAFT ASSEMBLY

  1. C165540E01
    Using SST, remove the rear drive shaft assembly as shown in the illustration.
    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    Remove the rear drive shaft assembly while keeping it level.


15. REMOVE REAR DRIVE SHAFT SNAP RING

  1. C057543E04
    Using a screwdriver, remove the rear drive shaft snap ring.


16. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

  1. C168602E01
    Using SST, remove the rear differential side gear shaft oil seal.
    SST
    09308-00010  

← COMPONENTS (from Jul 2010)REMOVAL (Aug 2008 – Jun 2010) →