REMOVAL
Removal / installation · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 2.
REMOVE REAR DIFFERENTIAL FILLER PLUG
|
 |
- Using a hexagon wrench (10 mm), remove the rear differential filler plug and rear differential filler plug gasket.
| 3.
REMOVE REAR DIFFERENTIAL DRAIN PLUG
|
 |
- Using a hexagon wrench (10 mm), remove the rear differential drain plug and rear differential drain plug gasket, and drain the oil.
| 4.
SEPARATE REAR SPEED SENSOR
|
 |
- Remove the bolt and separate the rear speed sensor from the rear axle carrier sub-assembly.
- NOTICE:
- Keep the sensor tip and rear speed sensor installation hole free from foreign matter.
| 5.
REMOVE REAR AXLE SHAFT NUT
|
 |
- Using SST and a hammer, release the staked part of the rear axle shaft nut.
- SST
- 09930-00010
- NOTICE:
- Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.
While applying the brakes, remove the rear axle shaft nut.
| 6.
SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
|
 |
- Remove the 2 bolts and separate the rear disc brake caliper assembly.
- NOTICE:
- Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.
| 7.
REMOVE REAR DISC
|
 |
- Put matchmarks on the rear disc and the axle hub.
- Release the parking brake and remove the rear disc.
- HINT:
- If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.
| 8.
REMOVE REAR AXLE HUB AND BEARING ASSEMBLY
|
 |
- Put matchmarks on the drive shaft and axle hub.
- NOTICE:
- Do not punch the marks.
- Remove the 4 bolts and the rear axle hub and bearing assembly.
- NOTICE:
- Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.
- Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable assembly.
| 9.
REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY
|
 |
- Remove the 2 bolts and separate the No. 3 parking brake cable assembly from the backing plate.
Remove the 2 bolts, 4 nuts, and the No. 3 parking brake cable assembly.


| 10.
REMOVE REAR STRUT ROD ASSEMBLY
|
 |
- Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.
- NOTICE:
- Since stopper nuts are used, loosen the bolts.
| 11.
REMOVE REAR AXLE CARRIER SUB-ASSEMBLY
|
 |
- Loosen the 2 bolts.
- NOTICE:
- Since stopper nuts are used, loosen the bolts.
- Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring (lower side) from the rear axle carrier sub-assembly.
- NOTICE:
- Be careful not to damage the outboard joint boot.
- Be careful not to damage the speed sensor rotor.
- Remove the 2 bolts, the 2 nuts, and the rear axle carrier sub-assembly.
- NOTICE:
- Be careful not to damage the outboard joint boot.
- Be careful not to damage the speed sensor rotor.
- HINT:
- Use wire or an equivalent tool to keep the rear drive shaft assembly from hanging down.
| 12.
REMOVE NO. 2 REAR SUSPENSION ARM ASSEMBLY
|
 |
Put matchmarks on the adjust cams and the rear suspension member sub-assembly.
Remove the nut, the No. 2 camber adjust cam, the rear suspension toe adjust cam sub-assembly, and the rear No. 2 suspension arm assembly LH.
- NOTICE:
- Mark the removed parts to distinguish left from right and keep them in order for reinstallation.
- HINT:
- When removing the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.
| 13.
REMOVE NO. 1 REAR SUSPENSION ARM ASSEMBLY
|
 |
Remove the bolt, the nut, and the rear No. 1 suspension arm assembly LH from the rear suspension member sub-assembly.
- NOTICE:
- Since a stopper nut is used, loosen the bolt.
| 14.
REMOVE REAR DRIVE SHAFT ASSEMBLY
|
 |
- Using SST, remove the rear drive shaft assembly as shown in the illustration.
- SST
- 09520-01010
09520-24010
(09520-32040)
- NOTICE:
- Remove the rear drive shaft assembly while keeping it level.
| 15.
REMOVE REAR DRIVE SHAFT SNAP RING
|
 |
- Using a screwdriver, remove the rear drive shaft snap ring.
| 16.
REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL |
 |
- Using SST, remove the rear differential side gear shaft oil seal.
- SST
- 09308-00010