2007-2013 Highlander Kluger · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C167673E01
    Connect the socket of the transmission control cable assembly to the shift lever assembly.

  1. Connect the control cable end to the shift lever assembly.

  1. Push the stopper cap to the socket as shown in the illustration.

  1. Turn the socket of the transmission control cable assembly clockwise and install the stopper cap.

    NOTICE:
    1. To prevent torsion of the inner cable, the end with protrusion should face up.
    2. Push the cable end to the bottom of the pin.
    3. Confirm that the connection between the socket and the shift lock control unit is secure.

  1. C167674
    Install the transmission control cable assembly with the 3 bolts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. C167675E02
    Connect the transmission control cable assembly to the No. 2 transmission control cable bracket.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. D025414E08
    Temporarily install the transmission control cable assembly to the control shaft lever with the nut.

  1. C089134
    Connect the transmission control cable assembly to the bracket with a new clip.


2. INSTALL AIR CONDITIONING UNIT

HINT:
(Click here)


3. INSTALL AIR CLEANER BRACKET

  1. A171820
    Install the 2 bolts and air cleaner bracket.

    Torque:
    12 N*m{ 123 kgf*cm , 9 ft.*lbf }


4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A170450
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose and connector.


5. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A171941E01
    Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. A170887
    Connect the 3 vacuum hoses.

  1. A171944
    Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.


7. INSTALL NO. 1 AIR CLEANER INLET

  1. A170454E01
    Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.


8. INSTALL NO. 2 AIR CLEANER INLET

  1. A170453
    Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.


9. INSTALL COOL AIR INTAKE DUCT SEAL

  1. A170196
    Install the cool air intake duct seal with the 11 clips.


10. INSTALL BATTERY

  1. A171858E01
    Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut B:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Install the positive battery terminal and nut.

  1. Connect the negative battery terminal, and tighten the nut.


11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


12. ADJUST SHIFT LEVER POSITION

  1. D025118
    Loosen the nut on the control shaft lever.

  1. D025119
    Push the control shaft fully downward.

  1. Return the control shaft lever 2 notches to the N position.

  1. C168468
    While pushing the control cable end up with the shift lever in the N position, install it to the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    1. If the control cable end is excessively pushed up, the shift lever cannot be adjusted.
    2. When tightening the nut, confirm that the control cable is properly stretched.

  1. Start the engine and make sure that the vehicle moves forward when shifting the lever from the N to the D position and moves rearward when shifting it to the R position.


13. INSPECT SHIFT LEVER POSITION
  1. When shifting from the P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into the position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N to the D position and moves rearward when shifting to the R position. If operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →