2007-2013 Highlander Kluger · Service Manual STEERING

EPS Warning Light Circuit

Circuit diagnosis · Vehicles built from Jul 2012

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

If the power steering ECU detects a malfunction, the P/S warning light comes on. At this time, the power steering ECU stores a DTC in its memory.

WIRING DIAGRAM

C170029E02
C170028E02

INSPECTION PROCEDURE


1. CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Using the intelligent tester, check for DTCs and confirm that there are no problems in the CAN communication system.

    OK:
    CAN DTCs are not output.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)
  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the item "IG Power Supply" in the Data List and read the value displayed on the intelligent tester.

    EMPS: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG Power Supply
    ECU power source voltage:
    Min.: 0 V
    Max.: 20.1531 V
    11 to 14 V
    Ignition switch on (IG)



NG
Go to step 4
OK


3. PERFORM ACTIVE TEST BY INTELLIGENT TESTER
  1. Enter the following menus: Body / Combination meter / Active Test.

  1. According to the display on tester, perform the "Active Test".

    Combination meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. EPS (*1)
    P/S Warning Light
    ON or OFF
    Confirm that the vehicle is stopped, engine idling
    Master Warning (*2)
    Master Warning Light
    ON or OFF
    Confirm that the vehicle is stopped, engine idling
    *1: w/o Multi-information Display*2: w/ Multi-information Display

    OK:
    Indicator comes on.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU (Click here)

4. INSPECT FUSE (ECU IG NO. 1)
  1. Remove the ECU IG No. 1 fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    OK:
    Below 1 Ω



NG
REPLACE FUSE
OK


5. CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)
C113533E09
  1. Disconnect the connectors from the power steering ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D5-5 (IG) - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D4-2 (PGND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Enter the following menus: Body / Combination meter / Active Test.

  1. According to the display on the tester, perform the "Active Test".

    Combination meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. EPS (*1)
    P/S Warning Light
    ON or OFF
    Confirm that the vehicle is stopped, engine idling
    Master Warning (*2)
    Master Warning Light
    ON or OFF
    Confirm that the vehicle is stopped, engine idling
    *1: w/o Multi-information Display*2: w/ Multi-information Display

    OK:
    Indicator comes on.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU (Click here)


← EPS Warning Light Circuit (Jul 2010 – Jun 2012)COMPONENTS (May 2007 – Jun 2010) →