2007-2013 Highlander Kluger · Service Manual STEERING

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B173224
    Disengage the 8 claws and guide, and remove the front door scuff plate LH.


5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.


6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. Disconnect each connector.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


7. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173021
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. B173009
    Disconnect each connector and the aspirator duct.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


8. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (for LHD)

  1. C165098
    Remove the 4 bolts.

  1. C165099
    Disengage the 2 hooks.

  1. C168059
    Pull out the driver side knee airbag assembly from the vehicle and support the driver side knee airbag assembly with one hand as shown in the illustration.

    NOTICE:
    When removing the driver side knee airbag assembly, do not pull the airbag wire harness.

  1. C168060E01
    Using a screwdriver with the tip wrapped with protective tape, disconnect the driver side knee airbag connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. C165102
    Disengage the 2 claws and separate the DLC3 from the driver side knee airbag assembly.


9. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)

  1. C165546
    Separate the wire harness clamp from the instrument panel junction block assembly.

  1. Disconnect the connectors from the instrument panel junction block assembly.

  1. Remove the 3 nuts.

  1. C165547
    Move the instrument panel junction block assembly and disengage the wire harness clamp.

  1. Disconnect the connectors from the back of the instrument panel junction block assembly.

  1. Remove the instrument panel junction block assembly.


10. REMOVE POWER STEERING ECU ASSEMBLY (for LHD)

  1. C165549E01
    Disconnect the 4 connectors from the power steering ECU assembly.

  1. C166319
    Remove the 3 nuts and the power steering ECU assembly.


11. REMOVE POWER STEERING ECU ASSEMBLY (for RHD)

  1. C165550E01
    Separate the wire harness clamp from the power steering ECU assembly.

  1. Disconnect the 4 connectors from the power steering ECU assembly.

  1. C166320
    Remove the 3 nuts and the power steering ECU assembly.

← REMOVAL (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →