2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE DECK BOARD ASSEMBLY

  1. B173240
    Remove the deck board assembly.


2. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)

  1. B173242
    Disengage the 2 guides and remove the No. 3 deck board sub-assembly.


3. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)

  1. B173244
    Disengage the 2 guides and remove the No. 2 deck board sub-assembly.


4. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.


5. REMOVE REAR MAT

  1. B173249
    Remove the rear mat.


6. REMOVE DECK TRIM SERVICE HOLE COVER

7. REMOVE LOWER SPARE WHEEL CARRIER HINGE COVER

8. REMOVE SPARE TIRE

9. REMOVE SPARE WHEEL CARRIER LOCK COVER

10. REMOVE REAR WHEELS

11. SEPARATE REAR STABILIZER LINK ASSEMBLY LH

  1. C167797E01
    Remove the nut and separate the rear stabilizer link assembly LH from the rear stabilizer bar.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.


12. SEPARATE REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


13. REMOVE REAR STABILIZER BAR

  1. C170677E01
    Remove the 4 bolts and rear stabilizer bar.


14. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

C167804
  1. Remove the bolt and the nut, and separate the rear No. 2 suspension arm assembly from the rear axle carrier sub-assembly.

    NOTICE:
    Since a stopper nut is used, loosen the bolt.

  1. Remove the bolt and the rear No. 2 suspension arm assembly.


15. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


16. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

C167805
  1. Remove the bolt and the nut, and separate the rear No. 1 suspension arm assembly from the rear axle carrier sub-assembly.

    NOTICE:
    Since a stopper nut is used, loosen the bolt.

  1. Remove the bolt and the rear No. 1 suspension arm assembly.


17. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


18. REMOVE EXHAUST PIPE CLAMP BRACKET SUB-ASSEMBLY

  1. C167807
    Separate the exhaust pipe clamp from the exhaust pipe clamp bracket sub-assembly.

  1. C167808
    Remove the 3 bolts and the exhaust pipe clamp bracket sub-assembly.


19. REMOVE REAR SUSPENSION MEMBER

  1. C167809
    Using a jack and 2 wooden blocks, and support the rear suspension member.

  1. Remove the 4 nuts, the 2 bolts, and the 4 rear lower suspension member stoppers.

    C167813E01

  1. C167811
    Lower the suspension member to the point shown in the illustration.

  1. C168180
    Remove the rear suspension member as shown in the illustration.

    NOTICE:
    When removing the rear suspension member, be careful not to damage the vehicle body or other components installed on the vehicle.


20. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH

  1. C168190E01
    Using SST and a press, remove the rear suspension member body mounting front cushion LH from the rear suspension member sub-assembly.
    SST
    09527-17011  
    09950-70010   (09951-07100)
    09950-60010   (09951-00340)

    HINT:
    1. Install SST as shown in the illustration.
    2. To prevent the rear suspension member sub-assembly from falling after removing the rear suspension member body mounting front cushion LH, support the rear suspension member sub-assembly using your hands and body while pressing.


21. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

HINT:
Perform the same procedure as the LH side.


22. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)

  1. C168188E01
    Using SST and a press, remove the rear suspension member body mounting rear cushion from the rear suspension member sub-assembly.
    SST
    09527-17011  
    09950-70010   (09951-07100)
    09950-60010   (09951-00340)

    HINT:
    1. Install SST as shown in the illustration.
    2. To prevent the rear suspension member sub-assembly from falling after removing the rear suspension member body mounting rear cushion, support the rear suspension member sub-assembly using your hands and body while pressing.


23. REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

HINT:
Perform the same procedure as the LH side.


24. REMOVE HOLE PLUG

  1. C168182
    Remove the 3 hole plugs from the rear suspension member sub-assembly.

    HINT:
    There are two sizes of hole plugs.


25. REMOVE STUD BOLT (for LH Side)

  1. C167815
    Remove the stud bolt.


26. REMOVE STUD BOLT (for RH Side)

HINT:
Perform the same procedure as the LH side.

← REMOVAL (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →