2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL STUD BOLT (for LH Side)

  1. C167815
    Install the stud bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }


2. INSTALL STUD BOLT (for RH Side)

HINT:
Perform the same procedure as the LH side.


3. INSTALL HOLE PLUG

  1. C168182
    Install the hole plugs to the rear suspension member sub-assembly.

    HINT:
    There are two sizes of hole plugs.


4. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH

  1. C167820
    Temporarily install a new rear suspension member body mounting front cushion LH to the position shown in the illustration.

  1. Using SST and a press, install the rear suspension member body mounting front cushion LH to the rear suspension member sub-assembly.

    C168165E01

    SST
    09950-70010   (09951-07100)
    09950-60020   (09951-00890)
    09502-12010  
    09515-30010  

    HINT:
    Slowly press in the mounting cushion.

  1. C168166
    While observing from the side, press in the rear suspension member body mounting front cushion LH until there is no clearance between the rear suspension member body mounting front cushion LH and the rear suspension member sub-assembly as shown in the illustration.

    NOTICE:
    Do not press the rear suspension member excessively, or it will easily deform.


5. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

  1. C167821
    Temporarily install a new rear suspension member body mounting front cushion RH to the position shown in the illustration.

  1. Using SST and a press, install the rear suspension member body mounting front cushion RH to the rear suspension member sub-assembly.

    C168181E01

    SST
    09950-70010   (09951-07100)
    09950-60020   (09951-00890)
    09502-12010  
    09515-30010  

    HINT:
    Slowly press in the mounting cushion.

  1. C168166
    While observing from the side, press in the rear suspension member body mounting front cushion RH until there is no clearance between the rear suspension member body mounting front cushion RH and the rear suspension member sub-assembly as shown in the illustration.

    NOTICE:
    Do not press the rear suspension member excessively, or it will easily deform.


6. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)

  1. C167819
    Temporarily install a new rear suspension member body mounting rear cushion (LH side) to the position shown in the illustration.

  1. Using SST and a press, install the rear suspension member body mounting rear cushion (LH side) to the rear suspension member sub-assembly.

    C168164E01

    SST
    09950-70010   (09951-07100)
    09950-60020   (09951-00890)
    09502-12010  
    09515-30010  

    HINT:
    Slowly press in the mounting cushion.

  1. C168166
    While observing from the side, press in the rear suspension member body mounting rear cushion (LH side) until there is no clearance between the rear suspension member body mounting rear cushion (LH side) and the rear suspension member sub-assembly as shown in the illustration.

    NOTICE:
    Do not press the rear suspension member excessively, or it will easily deform.


7. INSTALL REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

HINT:
Perform the same procedure as the LH side.


8. INSTALL REAR SUSPENSION MEMBER

  1. C167810
    Set the jack and wooden blocks below the vehicle as shown in the illustration.

  1. C167812
    Set the rear suspension member onto the jack as shown in the illustration.

    NOTICE:
    When removing the rear suspension member, be careful not to damage the vehicle body or other components installed on the vehicle.

  1. C167809
    Raise the rear suspension member with a jack.

  1. Install the rear suspension member and the rear lower suspension member stoppers LH and RH with the 4 nuts.

    C168169E01

    Torque:
    Nut A:
    55 N*m{ 561 kgf*cm , 40 ft.*lbf }
    Nut B:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Install the rear suspension member and the rear lower suspension member stoppers with the 2 bolts.

    C167814E02

    Torque:
    55 N*m{ 561 kgf*cm , 40 ft.*lbf }

    NOTICE:
    Be sure to install the rear suspension member with the rear lower suspension member stopper in the correct direction as shown in the illustration.


9. INSTALL EXHAUST PIPE CLAMP BRACKET SUB-ASSEMBLY

  1. C167808
    Install the exhaust pipe clamp bracket sub-assembly with the 3 bolts.

  1. C168179
    Install the exhaust pipe clamp to the exhaust pipe clamp bracket sub-assembly.


10. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

C167805E01
  1. Temporarily install the rear No. 1 suspension arm assembly to the rear suspension member with the bolt.

    NOTICE:
    Ensure that the identification mark faces the rear side of the vehicle.

  1. Temporarily install the rear No. 1 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and the nut.

    NOTICE:
    Since a stopper nut is used, temporarily tighten the bolt.


11. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


12. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

C170680E01
  1. Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member with the bolt.

    NOTICE:
    Ensure that the identification mark faces the rear side of the vehicle.

  1. Temporarily install the rear No. 2 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and the nut.

    NOTICE:
    Since a stopper nut is used, temporarily tighten the bolt.


13. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


14. STABILIZE SUSPENSION

  1. C167817E01
    Jack up the rear axle carrier, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the installed bolt of the rear No. 1 suspension arm (inner side) is horizontally aligned with the center of the rear axle hub.

    CAUTION:
    Do not jack up the rear axle carrier subassembly too high as the vehicle may fall.

    NOTICE:
    Do not bend the brake dust cover.

    HINT:
    1. If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier subassembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.
    2. Use the same procedures for the RH side and LH side.


15. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

  1. C167806E01
    Using SST and a socket wrench (19 mm), fully tighten the bolt.

    Torque:
    without SST:
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }
    with SST:
    89 N*m{ 904 kgf*cm , 65 ft.*lbf }

    SST
    09961-00950  

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 425 mm (16.73 in.).
    2. This torque value is effective when SST is parallel to the torque wrench.
    3. The final torque must be applied under standard vehicle height conditions.

  1. C170679
    Fully tighten the bolt

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


16. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


17. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

C167804E02
  1. Fully tighten the bolts.

    Torque:
    Bolt (A):
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }
    Bolt (B):
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


18. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


19. INSTALL REAR STABILIZER BAR

  1. C170677E01
    Install the rear stabilizer bar with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


20. INSTALL REAR STABILIZER LINK ASSEMBLY LH

  1. C167797E02
    Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.


21. INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


22. INSTALL REAR WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


23. INSTALL SPARE WHEEL CARRIER LOCK COVER

24. INSTALL SPARE TIRE

25. INSTALL LOWER SPARE WHEEL CARRIER HINGE COVER

26. INSTALL DECK TRIM SERVICE HOLE COVER

27. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


28. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


29. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


30. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


31. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board sub-assembly.


32. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

HINT:
Click here

← REMOVAL (from Jul 2010)INSTALLATION (Aug 2008 – Jun 2010) →