2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

Open in CAN Main Bus Line (RHD Models)

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
  1. CAN bus main wire or connector
  2. CAN junction connector CTR
  3. CAN junction connector RH
  4. ECM
  5. Combination meter

WIRING DIAGRAM

C170579E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If the doors need to be opened in order to check the connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.


1. CHECK DLC3

  1. C118856E59
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D47-6 (CANH) - D47-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    NOTICE:
    When the measured value is 133 Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3
OK


2. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR CTR)
  1. Turn the ignition switch off.

  1. Disconnect the CAN junction connector CTR.

  1. Measure the resistance according to the value(s) in the table below.C132298E32

    Standard resistance:
    Tester Connection
    Wiring Color
    Connect to
    Condition
    Specified Condition
    D47-1 (CANH) - D47-12 (CANL)
    SB - W
    CAN junction connector RH
    Ignition switch off
    108 to 132 Ω
    D47-5 (CANH) - D47-16 (CANL)
    R - W
    ECM
    Ignition switch off
    108 to 132 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (CAN junction connector main wire)
    B
    NG (ECM main wire)
    C



B
Go to step 3

C
Go to step 4
A

REPLACE CAN JUNCTION CONNECTOR CTR

3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM)
  1. Reconnect the CAN junction connector RH.

  1. Disconnect the ECM connector.

  1. C170023E04
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D32-33 (CANH) - D32-34 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR RH - ECM)
OK

REPLACE ECM (Click here)

4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR RH)
  1. Reconnect the CAN junction connector CTR.

  1. Disconnect the CAN junction connector RH.

  1. Measure the resistance according to the value(s) in the table below.C132298E33

    Standard resistance:
    Tester Connection
    Wiring Color
    Connect to
    Condition
    Specified Condition
    D51-3 (CANH) - D51-14 (CANL)
    R - W
    Combination meter
    Ignition switch off
    108 to 132 Ω
    D51-5 (CANH) - D51-16 (CANL)
    SB - W
    CAN junction connector CTR
    Ignition switch off
    108 to 132 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (Combination meter main wire)
    B
    NG (CAN junction connector)
    C



B
Go to step 5

C
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR CTR - CAN JUNCTION CONNECTOR RH)
A

REPLACE CAN JUNCTION CONNECTOR RH

5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER)
  1. Reconnect the CAN junction connector CTR.

  1. Disconnect the combination meter connector.

  1. C109571E21
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-25 (CANH) - E1-26 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN JUNCTION CONNECTOR CTR - COMBINATION METER)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Open in CAN Main Bus Line (RHD Models) (May 2007 – Jul 2008)Open in CAN Main Bus Line (RHD Models) (Jul 2010 – Jun 2012) →