Open in CAN Main Bus Line (RHD Models)
Circuit diagnosis · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012
DESCRIPTION
There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.| Symptom |
Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
- After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If the doors need to be opened in order to check the connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
- HINT:
- Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.
- Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK DLC3 |
Turn the ignition switch off.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D47-6 (CANH) - D47-14 (CANL)
Ignition switch off
108 to 132 Ω
- NOTICE:
- When the measured value is 133 Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.
|
|
||||
| OK | |
| 2. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR CTR) |
Turn the ignition switch off.
Disconnect the CAN junction connector CTR.
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
Tester Connection
Wiring Color
Connect to
Condition
Specified Condition
D47-1 (CANH) - D47-12 (CANL)
SB - W
CAN junction connector RH
Ignition switch off
108 to 132 Ω
D47-5 (CANH) - D47-16 (CANL)
R - W
ECM
Ignition switch off
108 to 132 Ω
- Result:
Result
Proceed to
OK
A
NG (CAN junction connector main wire)
B
NG (ECM main wire)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM) |
Reconnect the CAN junction connector RH.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
D32-33 (CANH) - D32-34 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
| 4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (CAN JUNCTION CONNECTOR RH) |
Reconnect the CAN junction connector CTR.
Disconnect the CAN junction connector RH.
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
Tester Connection
Wiring Color
Connect to
Condition
Specified Condition
D51-3 (CANH) - D51-14 (CANL)
R - W
Combination meter
Ignition switch off
108 to 132 Ω
D51-5 (CANH) - D51-16 (CANL)
SB - W
CAN junction connector CTR
Ignition switch off
108 to 132 Ω
- Result:
Result
Proceed to
OK
A
NG (Combination meter main wire)
B
NG (CAN junction connector)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER) |
Reconnect the CAN junction connector CTR.
Disconnect the combination meter connector.
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E1-25 (CANH) - E1-26 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
