DATA LIST / ACTIVE TEST
System information · Vehicles built May 2007 – Jun 2010
Versions by build date: May 2007 – Jun 2010 from Jul 2010
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester main switch on.
Select the following menu items: Powertrain / Cruise Control / Data List.
Read the Data List according to the display on the tester.
ECM (Cruise Control): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
CCS Vehicle Spd
Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
Actual vehicle speed
-
CCS Mem Vehicle Spd
Stored vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph)
Actual stored vehicle speed
-
Throttle Opening Angle
Required throttle opening angle / min.: 0°, max.: 125°
Actual required throttle opening angle
-
Cruise Control
Cruise control system active condition / ON or OFF
ON: Cruise control activated
OFF: Cruise control deactivated
-
CCS Main SW M-CPU
Main SW signal (Main CPU) / ON or OFF
ON: Main switch ON
OFF: Main switch OFF
"3"
CCS Ready M-CPU
Cruise control system standby condition (Main CPU) / ON or OFF
ON - OFF: Change ON/OFF each time main switch is pushed in.
"1"
CCS Indicator M-CPU
Cruise indicator signal (Main CPU) / ON or OFF
ON: "CRUISE" ON
OFF: "CRUISE" OFF
"2"
Cancel Switch
CANCEL SW signal / ON or OFF
ON: CANCEL Switch ON
OFF: CANCEL Switch OFF
-
SET/COAST Switch
-/SET SW signal / ON or OFF
ON: -/SET Switch ON
OFF: -/SET Switch OFF
-
RES/ACC Switch
+/RES SW signal / ON or OFF
ON: +/RES Switch ON
OFF: +/RES Switch OFF
-
Stop Light SW M-CPU
Stop light SW signal (Main CPU) / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Cruise Operation Status
Transmission range sensor signal / ON or OFF
ON: Shift lever in D or 4 position
OFF: Shift lever except in D or 4 position
-
#Codes
Number of DTC recorded / 0 to 255
Min.: 0
Max.: 4
-
- HINT:
- "3" is OK but "1" is NG → ECM failure
- "1" is OK but "2" is NG → DTC output or ECM failure
- "3" is OK but cruise indicator does not turn on → CRUISE main indicator, wire harness, or ECM failure
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester main switch on.
Select the following menu items: Body Electrical / Combination Meter / Active Test.
Perform "Active Test" according to the display on the tester.
- HINT:
- The ignition switch must be turned on to proceed with the Active Test using the intelligent tester.
Combination Meter: Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Lamp Cruise
CRUISE main indicator light
Indicator light BLINK / OFF
-