FREEZE FRAME DATA
Troubleshooting · Vehicles built from May 2007
| FREEZE FRAME DATA |
- NOTICE:
- It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
- Turn the ignition switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester.
- It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Check the freeze frame data by following the prompts on the intelligent tester display.
Power Steering ECU: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Meter Vehicle Velocity
Vehicle speed from meter:
Min.: 0 km/h (0 mph)
Max.: 300 km/h (187.5 mph)
0 km/h (mph)
Vehicle stopped
No significant fluctuation
Vehicle driven at a constant speed
Engine Revolution
Shows the engine speed:
Min.: 0 rpm
Max.: 12800 rpm
No significant fluctuation
Engine is running at a constant speed
Motor Actual Current
Amount of current to motor:
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
Power steering is in operation
Command Value Current
Demanded amount of current to motor:
Min.: -327.68 A
Max.: 327.68 A
Value changes in proportion to steering effort
Power steering is in operation
Steering Angle Velocity
Steering angle speed:
Min.: -32768°/sec.
Max.: 32767°/sec.
Value changes in proportion to steering effort
Steering wheel is turned
Thermistor Temperature
ECU substrate temperature:
Min.: -40°C
Max.: 150°C
-40 to 150°C
Ignition switch on (IG)
PIG Power Supply
Power source voltage to activate motor:
Min.: 0 V
Max.: 20.1531 V
11 to 14 V
Power steering is in operation
IG Power Supply
ECU power source voltage:
Min.: 0 V
Max.: 20.1531 V
11 to 14 V
Ignition switch on (IG)
Motor Rotation Angle
Motor rotation angle:
Min.: 0°
Max.: 360°
During steering operation, motor rotation angle value changes from 0 to 360°
Power steering is in operation
Motor Voltage
Motor power supply voltage:
Min.: 0 V
Max.: 45.955 V
11 to 14 V
Power steering is in operation
Motor Terminal Volt (U)
Motor terminal voltage (U phase):
Min.: 0 V
Max.: 46.667 V
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
Engine running and steering wheel is turned
Motor Terminal Volt (V)
Motor terminal voltage (V phase):
Min.: 0 V
Max.: 46.667 V
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
Engine running and steering wheel is turned
Motor Terminal Volt (W)
Motor Terminal voltage (W phase):
Min.: 0 V
Max.: 46.667 V
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
Engine running and steering wheel is turned
Battery Voltage
Battery voltage:
Min.: 0 V
Max.: 25.5 V
11 to 14 V
-
PS Assist Signal
Power steering assist signal:
ON or OFF
ON: Power steering assist signal is sent
Ignition switch on (IG) and steering wheel is turned
OFF: Power steering assist signal is not sent
No steering load (in centered position)