Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
Key Lock-in Prevention Function does not Work Properly
Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
When the key is in the ignition key cylinder or the door courtesy light ON signal is input to the main body ECU (instrument panel junction block), performing the door lock operation with the lock switch does not lock the door. WIRING DIAGRAM
INSPECTION PROCEDURE
1. READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH)
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select Key Unlock Warning SW in the Data List and read the tester display.
Main Body (Main Body ECU):
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Key Unlock Warning SW
Unlock warning switch signal/ON or OFF
ON: Key is in ignition key cylinder OFF: No key is in ignition key cylinder
-
OK:
The intelligent tester displays ON or OFF according to whether the key is in the ignition key cylinder.
NG
OK
2. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE DOOR COURTESY LIGHT SWITCH)
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select D Door Courtesy SW in the Data List and read the tester display.
Main Body (Main Body ECU):
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Courtesy SW
Driver side door courtesy light switch signal/ON or OFF
ON: Driver side door is open OFF: Driver side door is closed
-
OK:
The intelligent tester displays ON or OFF according to whether the driver side door is open or closed.
NG
OK
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
3. INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
Remove the driver side door courtesy light switch (Click here ).
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
1 - Switch ground
Not pushed (ON)
Below 1 Ω
1 - Switch ground
Pushed (OFF)
10 kΩ or higher
NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here )
OK
4. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH CIRCUIT)
Disconnect the main body ECU (instrument panel junction block) connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LHD:
Tester Connection
Condition
Specified Condition
O2-1 - D7-24 (DCTY)
Always
Below 1 Ω
O2-1 - Body ground
Always
10 kΩ or higher
for RHD:
Tester Connection
Condition
Specified Condition
N2-1 - D7-24 (DCTY)
Always
Below 1 Ω
N2-1 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
5. INSPECT UNLOCK WARNING SWITCH ASSEMBLY
Remove the unlock warning switch (Click here ).
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Pushed
Below 1 Ω
1 - 2
Not pushed
10 kΩ or higher
NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here )
OK
6. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH CIRCUIT)
Disconnect the main body ECU (instrument panel junction block) connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
D16-1 - D9-5 (KSW)
Always
Below 1 Ω
D16-1 - Body ground
Always
10 kΩ or higher
D16-2 - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)