2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Key Lock-in Prevention Function does not Work Properly

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the key is in the ignition key cylinder or the door courtesy light ON signal is input to the main body ECU (instrument panel junction block), performing the door lock operation with the lock switch does not lock the door.

WIRING DIAGRAM

B171389E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select Key Unlock Warning SW in the Data List and read the tester display.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal/ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -

    OK:
    The intelligent tester displays ON or OFF according to whether the key is in the ignition key cylinder.



NG
Go to step 5
OK


2. READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE DOOR COURTESY LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select D Door Courtesy SW in the Data List and read the tester display.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy light switch signal/ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -

    OK:
    The intelligent tester displays ON or OFF according to whether the driver side door is open or closed.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

3. INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

  1. B111600E07
    Remove the driver side door courtesy light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Switch ground
    Not pushed (ON)
    Below 1 Ω
    1 - Switch ground
    Pushed (OFF)
    10 kΩ or higher



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH CIRCUIT)

  1. B171390E02
    Disconnect the main body ECU (instrument panel junction block) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    O2-1 - D7-24 (DCTY)
    Always
    Below 1 Ω
    O2-1 - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    N2-1 - D7-24 (DCTY)
    Always
    Below 1 Ω
    N2-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

5. INSPECT UNLOCK WARNING SWITCH ASSEMBLY

  1. B164411E01
    Remove the unlock warning switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Not pushed
    10 kΩ or higher



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH CIRCUIT)

  1. B171391E02
    Disconnect the main body ECU (instrument panel junction block) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-1 - D9-5 (KSW)
    Always
    Below 1 Ω
    D16-1 - Body ground
    Always
    10 kΩ or higher
    D16-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← Key Lock-in Prevention Function does not Work Properly (Aug 2008 – Jun 2010)PRECAUTION (May 2007 – Jul 2008) →