2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

  1. A129648
    Using a 19 mm deep socket wrench, install the engine coolant temperature sensor and a new gasket.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }


2. INSTALL KNOCK CONTROL SENSOR

  1. A132951E03
    Install the 2 knock control sensors with the 2 bolts as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 knock control sensor connectors.


3. INSTALL KNOCK CONTROL SENSOR WIRE

  1. A171877
    Connect the 2 knock control sensor connectors and 3 clamps.


4. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

  1. P012478E01
    Clean the threads of the oil pressure switch. Apply adhesive to 2 or 3 threads of the oil pressure switch assembly.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. A139194
    Using a 24 mm deep socket wrench, install the oil pressure switch.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation to prevent oil leaks.


5. INSTALL NO. 1 VACUUM SWITCHING VALVE

  1. A132992
    Install the bolt and No. 1 vacuum switching valve.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


6. INSTALL RADIO SETTING CONDENSER

  1. A132991
    Install the 2 bolts and 2 radio setting condensers.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


7. INSTALL WATER PUMP PULLEY

  1. A128112E01
    Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


8. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A129645E01
    Install the No. 2 idler pulley sub-assembly and cover plate with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


9. INSTALL NO. 2 TIMING GEAR COVER

  1. A132987
    Install the No. 2 timing gear cover with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


10. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A129644E01
    Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.

    HINT:
    Each bolt length is as follows:
    A: 70 mm (2.76 in.)
    B: 33 mm (1.30 in.)

  1. Install the V-ribbed belt tensioner assembly by tightening the bolt 1 and bolt 2 in the order shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


11. INSTALL GENERATOR ASSEMBLY

  1. A170743
    Install the wire harness clamp bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A170150
    Connect the generator bracket with the wire harness clamp.

  1. A170146
    Install generator assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. A170145
    Temporarily install the 2 bolts.

  1. A170145
    Fully tighten the 2bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A170144
    Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 3 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.


12. INSTALL TRANSVERSE ENGINE MOUNTING BRACKET (for 4WD)

  1. A143881
    Install the transverse engine mounting bracket with the 3 bolts.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }


13. INSTALL TRANSVERSE ENGINE MOUNTING BRACKET (for 2WD)

  1. A163583
    Install the transverse engine mounting bracket with the 3 bolts.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }


14. INSTALL TRANSVERSE ENGINE MOUNTING BRACKET

  1. A129642
    Install the engine mounting bracket RH with the 3 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }


15. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A129649E01
    Install a new gasket as shown in the illustration.

  1. A129641E01
    Install the exhaust manifold sub-assembly LH with the 6 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


16. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A140784
    Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }


17. INSTALL NO. 2 MANIFOLD STAY

  1. A140783E01
    Install the No. 2 manifold stay with the bolt and nut in the order shown in the illustration.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


18. INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A171896
    Install a new O-ring to the No. 2 engine oil level dipstick guide.

  1. Apply a light coat of engine oil to the O-rings.

  1. Push in the No. 2 engine oil level dipstick guide end into the No. 1 engine oil level dipstick guide.

  1. A171871
    Install the No. 2 engine oil level dipstick guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the engine oil level dipstick.


19. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A129650E01
    Install a new gasket as shown in the illustration.

  1. A140781E01
    Install the exhaust manifold sub-assembly RH with the 6 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


20. INSTALL INTAKE MANIFOLD

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Intake Manifold and Cylinder Head Sub-assembly RH
Intake Manifold and Cylinder Head Sub-assembly LH

  1. A134933
    Set a new gasket on each cylinder head.

    NOTICE:
    1. Align the port holes of the gasket and cylinder head.
    2. Make sure that the gasket is installed in the correct direction.

  1. Set the intake manifold on the cylinder heads.

  1. Install and tighten the 6 bolts and 4 nuts uniformly in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


21. INSTALL NO. 2 ENGINE MOUNTING STAY RH

  1. A162388
    Install the No. 2 mounting stay RH with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


22. INSTALL IGNITION COIL ASSEMBLY (for LHD)

  1. A134966E01
    Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 6 ignition coil connectors.

  1. A170201E01
    Install the 4 bolts [A].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the nut [B].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the 2 clamps [C].


23. INSTALL IGNITION COIL ASSEMBLY (for RHD)

  1. A134966E01
    Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 6 ignition coil connectors.

  1. A170203E01
    Install the 2 bolts [D].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the nut [E].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the 2 clamps [F].


24. INSTALL ENGINE HANGERS
  1. Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 Engine hanger 12281-31120
    No. 2 Engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.


25. REMOVE ENGINE STAND
← REASSEMBLY (from Aug 2013)INSTALLATION (Aug 2008 – Jun 2010) →