2007-2013 Highlander Kluger · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.

  2. A103809E15
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
    1. 3 data sets before the DTC was set
    2. 1 data set when the DTC was set
    3. 1 data set after the DTC was set
    These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying of the cause of the malfunction, and in judging whether it was temporary or not.


LIST OF FREEZE FRAME DATA
Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Calculated load by ECM
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If approximately 0.0 g/sec.:
  1. Mass air flow meter sub-assembly power source circuit open or shorted
  1. VG circuit open or shorted
If 271.0 g/sec. or more:
  1. E2G circuit open
Atmosphere Pressure
Atmosphere pressure
-
Coolant Temp
Engine coolant temperature
If value -40°C (-40°F), sensor circuit open
If value 140°C (284°F), sensor circuit shorted
Intake Air
Intake air temperature
If value -40°C (-40°F), sensor circuit open
If value 140°C (284°F), sensor circuit shorted
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Battery Voltage
Battery voltage
-
Accel Sens. No. 1 Volt %
Absolute accelerator pedal position No. 1
-
Accel Sens. No. 2 Volt %
Absolute accelerator pedal position No. 2
-
Throttle Sensor Volt %
Absolute throttle position No. 1
-
Throttl Sensor #2 Volt %
Absolute throttle sensor positioning No. 2
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Motor DUTY
Throttle actuator
-
Throttle Position
Throttle position
When the engine stalls, is difficult to start, or idles roughly
ISC Flow
Flow rate calculated using information from each sensor
When the engine stalls, is difficult to start, or idles roughly
ISC Position
Requested opening amount calculated using ISC
When the engine stalls, is difficult to start, or idles roughly
ISC Feedback Value
ISC feedback compensation amount
When the engine stalls, is difficult to start, or idles roughly
ISC Learning Value
ISC learned compensation amount
When the engine stalls, is difficult to start, or idles roughly
Electric Load Feedback Val
Compensation flow rate according to electrical load
When the engine stalls, is difficult to start, or idles roughly
Air Conditioner FB Val
Compensation flow rate according to air conditioner load
When the engine stalls, is difficult to start, or idles roughly
Low Revolution Control
Low engine speed control operation state
When the engine stalls, is difficult to start, or idles roughly
N Range Status
Shift lever N status
When the engine stalls, is difficult to start, or idles roughly
Eng Stall Control FB Flow
Intake air compensation flow rate
When the engine stalls, is difficult to start, or idles roughly
Deposit Loss Flow
Flow loss due to deposits
When the engine stalls, is difficult to start, or idles roughly
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump Speed Control
Fuel pump speed control status
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP Purge VSV
EVAP Purge VSV
-
Purge Cut VSV Duty
Purge cut VSV duty
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at air fuel ratio sensor
-
AF Lambda B2S1
Fuel trim at air fuel ratio sensor
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage
-
AFS voltage B2S1
Air fuel ratio sensor output voltage
-
AFS Current B1S1
Air fuel ratio sensor current
-
AFS Current B2S1
Air fuel ratio sensor current
-
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio (bank 1 sensor 1)
-
A/F Heater Duty #2
Air fuel ratio sensor heater duty ratio (bank 2 sensor 1)
-
O2S B1S2
Heated oxygen sensor output voltage
-
O2S B2S2
Heated oxygen sensor output voltage
-
O2 Heater B1S2
Heated oxygen sensor heater (bank 1 sensor 2)
-
O2 Heater B2S2
Heated oxygen sensor heater (bank 2 sensor 2)
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current (bank 1 sensor 2)
-
O2 Heater Curr Val B2S2
Heated oxygen sensor current (bank 2 sensor 2)
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air fuel ratio
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve
Total FT #1
Total fuel trim (bank 1)
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
Long FT #2
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central valve
Total FT #2
Total fuel trim (bank 2)
-
Fuel System Status #1
Fuel system status (bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  3. OLDrive: Open loop due to driving conditions (fuel enrichment)
  4. OLFault: Open loop due to detected system fault
  5. CLFault: Closed loop but air fuel ratio sensor, which used for fuel control, malfunctioning
Fuel System Status #2
Fuel system status (bank 2)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  3. OLDrive: Open loop due to driving conditions (fuel enrichment)
  4. OLFault: Open loop due to detected system fault
  5. CLFault: Closed loop but air fuel ratio sensor, which used for fuel control, malfunctioning
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)
When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)
When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)
When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)
When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #5
Individual cylinder timing advance compensation amount (No. 5)
When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #6
Individual cylinder timing advance compensation amount (No. 6)
When the engine stalls, is difficult to start, or idles roughly
ACIS VSV
Intake air control valve for Acoustic Control Induction System (ACIS)
-
AICV VSV
VSV for air intake control valve
-
Actual VVT Angle #1
Actual VVT angle (bank 1)
-
Actual VVT Angle #2
Actual VVT angle (bank 2)
-
Actual VVT Ex Angle #1
Actual exhaust VVT angle (bank 1)
-
Actual VVT Ex Angle #2
Actual exhaust VVT angle (bank 2)
-
VVT Control Status #1
VVT control status (bank 1)
-
VVT Control Status #2
VVT control status (bank 2)
-
VVT Advance Fail
VVT control failure status
-
Catalyst Temp B1S1
Estimated catalyst temperature (bank 1 sensor 1)
-
Catalyst Temp B2S1
Estimated catalyst temperature (bank 2 sensor 1)
-
Catalyst Temp B1S2
Estimated catalyst temperature (bank 1 sensor 2)
-
Catalyst Temp B2S2
Estimated catalyst temperature (bank 2 sensor 2)
-
Starter Signal
Starter signal
-
Starter Control
Starter status
-
Power Steering Signal
Power steering switch
-
Starter Relay
Starter relay status
-
ACC Relay
ACC relay status
-
Neutral Position SW Signal
Park/neutral position switch signal
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Idle Up Signal
Idle up signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
Dist Batt Cable Disconnect
Total distance vehicle driven after battery cable disconnected
-
IG OFF Elapsed Time
Time after ignition switch off
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
Cylinder #5 Misfire Count
Cylinder #5 misfire count
-
Cylinder #6 Misfire Count
Cylinder #6 misfire count
-
All Cylinders Misfire Count
All cylinders misfire
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Catalyst OT MF F/C
Fuel cut to prevent catalyst from overheating during misfire
-
Cat OT MF F/C History
Catalyst Over Temp Misfire prevention F/C History
-
Cat OT MF F/C Cylinder #1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
-
Engine Speed (Starter Off)
Engine speed when starter off
When the engine stalls, is difficult to start, or idles roughly
Starter Count
Number of times starter turned on after ignition switch on (IG)
When the engine stalls, is difficult to start, or idles roughly
Run Dist of Previous Trip
Distance driven during previous trip
  1. Run Dist of Previous Trip continues to display the distance traveled in the previous trip during the detection period of DTC P1604, which ends 5 seconds after the engine starts.
    Then the previous trip distance will be cleared and the distance traveled during this trip, which is calculated based on the vehicle speed, will be displayed.
  2. When the engine is difficult to start and DTC P1604 is stored, Run Dist of Previous Trip will continue to be displayed.
    When inspecting for DTCs other than P1604, or when taking a snapshot, the distance traveled during this trip will be displayed.
Engine Starting Time
Time elapsed after engine started (interval between ignition switch on (IG) and off)
When the engine stalls, is difficult to start, or idles roughly
Previous Trip Coolant Temp
Engine coolant temperature during previous trip
When the engine stalls, is difficult to start, or idles roughly
Previous Trip Intake Temp
Intake air temperature during previous trip
When the engine stalls, is difficult to start, or idles roughly.
Engine Oil Temperature
Engine oil temperature (estimated temperature)
When the engine stalls, is difficult to start, or idles roughly
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip
When the engine stalls, is difficult to start, or idles roughly
Ambient Temp for A/C
Ambient temperature for A/C
When the engine stalls, is difficult to start, or idles roughly
Previous Trip Ambient Temp
Ambient temperature during previous trip
When the engine stalls, is difficult to start, or idles roughly
Engine Start Hesitation
History of hesitation during engine start
-
Low Rev for Eng Start
History of low engine speed after engine start
-
Minimum Engine Speed
Minimum engine speed
When the engine stalls, is difficult to start, or idles roughly
Fuel Cut Elaps Time
Elapsed time since fuel cut due to high engine speed
-
A/F Learn Value Idle #1
Air fuel ratio learn value of idle area (bank 1)
-
A/F Learn Value Low #1
Air fuel ratio learn value of low load area (bank 1)
-
A/F Learn Value Mid1 #1
Air fuel ratio learn value of middle1 load area (bank 1)
-
A/F Learn Value Mid2 #1
Air fuel ratio learn value of middle2 load area (bank 1)
-
A/F Learn Value High #1
Air fuel ratio learn value of high load area (bank 1)
-
A/F Learn Value Idle #2
Air fuel ratio learn value of idle area (bank 2)
-
A/F Learn Value Low #2
Air fuel ratio learn value of low load area (bank 2)
-
A/F Learn Value Mid1 #2
Air fuel ratio learn value of middle1 load area (bank 2)
-
A/F Learn Value Mid2 #2
Air fuel ratio learn value of middle2 load area (bank 2)
-
A/F Learn Value High #2
Air fuel ratio learn value of high load area (bank 2)
-
ACM Inhibit
ACM inhibit
-
ACM
ACM control status
-
Idle Fuel Cut
Fuel cut idle
ON: when throttle valve fully closed and engine speed over 1400 rpm
FC TAU
Fuel cut during very light load
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
Immobiliser Fuel Cut
Status of immobiliser fuel cut
-
Immobiliser Fuel Cut History
Status of immobiliser fuel cut history
-
Electrical Load Signal1
Electrical load signal
-
Electrical Load Signal2
Electrical load signal
-
← FREEZE FRAME DATA (May 2007 – Jun 2010)CHECK MODE PROCEDURE (from May 2007) →