2007-2013 Highlander Kluger · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


DESCRIPTION
  1. Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.


  1. A103809E15
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.
    1. 3 data set before the DTC was set.
    2. 1 data set when the DTC was set.
    3. 1 data set after the DTC was set.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying of the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA
LABEL
(Intelligent Tester Display)
Measure Item/Range
Diagnostic Note
Trouble Code
Freeze DTC
-
Injector
Injector
-
IGN Advance
Ignition advance
-
Calculate load
Calculate load
Calculated load by ECM
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If value is approximately 0.0 g/s:
  1. Mass air flow meter power source circuit open or shorted
  1. VG circuit open or shorted
If value is 160.0 g/s or more:
  1. E2G circuit open
Engine Speed
Engine speed
-
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Coolant Temp
Engine coolant temperature
If value is -40°C, sensor circuit open
If value is 140°C, sensor circuit shorted
Intake Air
Intake air temperature
If value is -40°C, sensor circuit open
If value is 140°C, sensor circuit shorted
Air-Fuel Ratio
Air-fuel ratio
-
Purge Density Learn Value
Learning value of purge density
-
Purge Flow
Purge flow
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Knock Correct Learn Value
Correction learning value of knocking
-
Knock Feedback Value
Feedback value of knocking
-
Accelerator Position No. 1
Absolute accelerator pedal position No. 1
-
Accelerator Position No. 2
Absolute accelerator pedal position No. 2
-
Throttle Position
Throttle position
Read value with ignition switch on (IG) (Do not start engine)
Throttle Sensor Position
Throttle sensor positioning
Read value with ignition switch on (IG) (Do not start engine)
Throttle Sensor Position #2
Throttle sensor positioning #2
-
Throttle Motor
Throttle actuator
-
O2S B1 S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for air fuel ratio sensor function of Active Test enables technician to check output voltage of sensor
O2S B2 S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for air fuel ratio sensor function of Active Test enables technician to check output voltage of sensor
AFS B1 S1
Air fuel ratio sensor output
Performing Control the Injection Volume or Control the Injection Volume for air fuel ratio sensor function of Active Test enables technician to check output voltage of sensor
AFS B2 S1
Air fuel ratio sensor output
Performing Control the Injection Volume or Control the Injection Volume for air fuel ratio sensor function of Active Test enables technician to check output voltage of sensor
AFS B2 S1
Air fuel ratio sensor current
-
Total FT #1
Total fuel trim
-
Total FT #2
Total fuel trim
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central valve
Short FT #2
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #2
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central valve
Fuel System Status (Bank 1)
Fuel system status (Bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  1. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  1. OL FAULT: Open loop due to detected system fault
  1. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
Fuel System Status (Bank 2)
Fuel system status (Bank 2)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
  1. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
  1. OL FAULT: Open loop due to detected system fault
  1. CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
AF FT B1 S1
Fuel trim at air fuel ratio sensor
-
AF FT B1 S1
Air fuel ratio sensor current
-
AF FT B2 S1
Fuel trim at air fuel ratio sensor
-
Catalyst Temp (B1 S1)
Catalyst temperature
-
Catalyst Temp (B2 S1)
Catalyst temperature
-
Catalyst Temp (B1 S2)
Catalyst temperature
-
Catalyst Temp (B2 S2)
Catalyst temperature
-
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Injection Volume (Cylinder 1)
Injection volume
-
Starter Signal
Starter signal
-
Power Steering Switch
Power steering signal
-
Power Steering Signal
Power steering signal (history)
Signal status usually ON until ignition switch turned off
Closed Throttle Position SW
Closed throttle position switch
-
A/C Signal
Air conditioning signal
-
Neutral Position SW Signal
PNP switch signal
-
Electrical Load Signal
Electrical load signal
-
Stop Light Switch
Stop light switch
-
Battery Voltage
Battery voltage
-
Atmosphere Pressure
Atmospheric pressure
-
Fuel Pump Speed Control
Fuel pump speed control status
-
ACIS VSV
ACIS VSV
-
VVT Control Status (Bank 2)
VVT control status (bank 2)
-
EVAP Purge VSV
VSV for EVAP
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
VVT Control Status (Bank 1)
VVT control status (bank 1)
-
Electric Fan Motor
Electric fan motor
ON: Operate
AICV VSV
AICV VSV
-
TC and TE1
TC and TE1 terminals of DLC3
-
ACM
Active control mount VSV duty ratio
-
VVT Aim Angle (Bank 1)
VVT aim angle (bank 1)
-
VVT Change Angle (Bank 1)
VVT change angle (bank 1)
-
VVT OCV Duty (Bank 1)
VVT OCV operation duty (bank 1)
-
VVT Ex Hold Lrn Val
VVT exhaust hold duty ratio learning value (bank 1)
-
VVT Ex Chg Angle (Bank 1)
VV exhaust change angle (bank 1)
-
VVT Ex OCV Duty (Bank 1)
VVT exhaust OCV duty (bank 1)
-
VVT Aim Angle (Bank 2)
VVT aim angle (bank 2)
-
VVT Change Angle (Bank 2)
VVT change angle (bank 2)
-
VVT OCV Duty (Bank 2)
VVT OCV operation duty (bank 2)
-
VVT Ex Hold Lrn Val (Bank 2)
VVT exhaust hold duty ration learning value (bank 2)
-
VVT Ex Chg Angle (Bank 2)
VVT exhaust change angle (bank 2)
-
VVT Ex OCV Duty (Bank 2)
VVT exhaust OCV duty (bank 2)
-
Idle Fuel Cut
Idle fuel cut
ON: when throttle valve fully closed and engine speed over 1500 rpm
FC TAU
FC TAU
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
Ignition
Ignition
-
Cylinder #1 Misfire Rate
Cylinder #1 misfire rate
Displayed in only idling
Cylinder #2 Misfire Rate
Cylinder #2 misfire rate
Displayed in only idling
Cylinder #3 Misfire Rate
Cylinder #3 misfire rate
Displayed in only idling
Cylinder #4 Misfire Rate
Cylinder #4 misfire rate
Displayed in only idling
Cylinder #5 Misfire Rate
Cylinder #5 misfire rate
Displayed in only idling
Cylinder #6 Misfire Rate
Cylinder #6 misfire rate
Displayed in only idling
All Cylinders Misfire Rate
All cylinder misfire rate
Displayed in only idling
Misfire RPM
Misfire RPM
-
Misfire Load
Misfire load
-
Misfire Margin
Misfire monitoring
-
Engine Run Time
Accumulated engine running time
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
← DTC CHECK / CLEAR (from Jul 2010)FREEZE FRAME DATA (from Jul 2010) →