2007-2013 Highlander Kluger · Service Manual ENGINE

P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

A flat type knock sensor (non-resonant type) has a structure that can detect vibrations over a wide band of frequencies: between approximately 6 kHz and 15 kHz.
Knock sensors are fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
DTC No.
DTC Detection Condition
Trouble Area
P0327
P0332
Output voltage of knock sensor 1 or 2 is less than 0.5 V (1 trip detection logic)
  1. Short in knock sensor 1 or 2 circuit
  2. Knock sensor 1 or 2
  3. ECM
P0328
P0333
Output voltage of knock sensor 1 or 2 is more than 4.5 V (1 trip detection logic)
  1. Open in knock sensor 1 or 2 circuit
  2. Knock sensor 1 or 2
  3. ECM

HINT:
When any of DTCs P0327, P0328, P0332 and P0333 are set, the ECM enters fail-safe mode. During fail- safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.

Reference: Inspection using an oscilloscope
A140638E02
The correct waveform is as shown.
Item
Content
Terminals
KNK1 - EKNK or KNK2 - EKN2
Equipment Settings
0.01 to 10 V/DIV., 0.01 to 10 ms./DIV.
Conditions
Keep engine speed at 4000 rpm with warm engine

WIRING DIAGRAM

A136096E06

INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.
  2. DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ VALUE USING DTC OUTPUT (CHECK KNOCK SENSOR CIRCUIT)

  1. A168205E01
    Disconnect the Bd1 connector.

  1. Using lead wires, connect the connectors as follows.

    Male Connector - Female Connector
    Terminal 2 - Terminal 4
    Terminal 1 - Terminal 3
    Terminal 4 - Terminal 2
    Terminal 3 - Terminal 1

  1. Warm up the engine.

  1. Run the engine at 3000 rpm for 10 seconds or more.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester on.

  1. Select the items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display
    Proceed to
    DTCs that are same as when vehicle brought in P0327, P0328 → P0327, P0328 or P0332, P0333 → P0332, P0333
    A
    DTCs that are different from when vehicle brought in P0327, P0328 → P0332, P0333 or P0332, P0333 → P0327, P0328
    B

  1. Reconnect the Bd1 connector.



B
Go to step 4
A


2. CHECK HARNESS OR CONNECTOR (CONNECTOR - ECM)

  1. A114617E10
    Disconnect the Bd1 connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    Bd1 female connector 2 - B2-29 (KNK1)
    Always
    Below 1 Ω
    Bd1 female connector 1 - B2-28 (EKNK)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    Bd1 female connector 4 - B2-21 (KNK2)
    Always
    Below 1 Ω
    Bd1 female connector 3 - B2-20 (EKN2)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    Bd1 female connector 2 or B2-29 (KNK1) - Body ground
    Always
    10 kΩ or higher
    Bd1 female connector 1 or B2-28 (EKNK) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    Bd1 female connector 4 or B2-21 (KNK2) - Body ground
    Always
    10 kΩ or higher
    Bd1 female connector 3 or B2-20 (EKN2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM

  1. A168206E02
    Disconnect the ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Bank 1:
    Tester Connection
    Switch Condition
    Specified Condition
    B2-29 (KNK1) - B2-28 (EKNK)
    Ignition switch on (IG)
    4.5 to 5.5 V
    Bank 2:
    Tester Connection
    Switch Condition
    Specified Condition
    B2-21 (KNK2) - B2-20 (EKN2)
    Ignition switch on (IG)
    4.5 to 5.5 V

  1. Reconnect the ECM connector.

    NOTICE:
    Fault may be intermittent. Check the wire harness and connectors carefully and retest.



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. INSPECT KNOCK SENSOR

  1. A168204E01
    Disconnect the Bd1 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Bd1 male connector 1 - 2
    Always
    120 to 280 kΩ
    Bd1 male connector 3 - 4
    Always
    120 to 280 kΩ

  1. Reconnect the connector.



NG
Go to step 5
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

5. CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR)

HINT:
  1. If DTC P0327 or P0328 has changed to P0332 or P0333, check the knock sensor circuit on the right bank side.
  2. If DTC P0332 or P0333 has changed to P0327 or P0328, check the knock sensor circuit on the left bank side.

  1. A114618E10
    Disconnect the Bd1 connector.

  1. Disconnect the knock sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    Bd1 male connector 2 - d2-2
    Always
    Below 1 Ω
    Bd1 male connector 1 - d2-1
    Always
    Below 1 Ω
    Bd1 male connector 4 - d1-2
    Always
    Below 1 Ω
    Bd1 male connector 3 - d1-1
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    Bd1 male connector 2 or d2-2 - Body ground
    Always
    10 kΩ or higher
    Bd1 male connector 1 or d2-1 - Body ground
    Always
    10 kΩ or higher
    Bd1 male connector 4 or d1-2 - Body ground
    Always
    10 kΩ or higher
    Bd1 male connector 3 or d1-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the connector.

  1. Reconnect the knock sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR (Click here)


← P0300 Random / Multiple Cylinder Misfire Detected (+ 6 more codes) (from Aug 2013)P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328, P0332, P0333) (Aug 2008 – Jun 2010) →