2007-2013 Highlander Kluger · Service Manual ENGINE

P0102 Mass or Volume Air Flow Circuit Low Input

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and to provide appropriate air fuel ratio. Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, changing their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the mass air flow meter sub-assembly. The voltage level is proportional to the air flow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor provide a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.

A165052E20
DTC No.
DTC Detection Condition
Trouble Area
P0102
Mass air flow meter sub-assembly voltage is below 0.2 V for 3 seconds
(1 trip detection logic)
  1. Open or short in mass air flow meter sub-assembly circuit
  2. Short in ground circuit
  3. Mass air flow meter sub-assembly
  4. ECM
P0103
Mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds
(1 trip detection logic)
  1. Open or short in mass air flow meter sub-assembly circuit
  2. Mass air flow meter sub-assembly
  3. ECM

HINT:
When any of these DTCs are set, check the air flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Air Flow Rate (gm/s)
Malfunctions
Approximately 0.0
  1. Open in mass air flow meter sub-assembly power source circuit
  2. Open or short in VG circuit
271.0 or more
Open in E2G circuit

WIRING DIAGRAM

A117876E20

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    DTC P0102 is output
    A
    DTC P0103 is output
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)

  1. A194097E43
    Disconnect the mass air flow meter sub-assembly connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B10-3 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Mass Air Flow Meter Sub-assembly)

  1. Reconnect the mass air flow meter sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EFI RELAY)
OK


3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B10-5 (VG) - B49-14 (VG)
    Always
    Below 1 Ω
    B10-4 (E2G) - B49-13 (E2G)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B10-5 (VG) or B49-14 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter sub-assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
OK


4. INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
  1. Perform On-vehicle Inspection (Click here).

  1. Inspect the function of the mass air flow meter sub-assembly.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

    5. Start the engine.

    6. Check that the reading of the mass air flow meter sub-assembly changes when the engine is raced.

      OK:
      The reading changes.



NG
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)

5. CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

  1. A194097E44
    Disconnect the mass air flow meter sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B10-4 (E2G) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Mass Air Flow Meter Sub-assembly)

  1. Reconnect the mass air flow meter sub-assembly connector.



NG
Go to step 6
OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)

6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B10-4 (E2G) - B49-13 (E2G)
    Always
    Below 1 Ω

  1. Reconnect the mass air flow meter sub-assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)


← P0100 Mass or Volume Air Flow Circuit (+ P0102, P0103) (Aug 2008 – Jun 2010)P0110 Intake Air Temperature Circuit (+ P0112, P0113) (May 2007 – Jul 2008) →