2007-2013 Highlander Kluger · Service Manual ENGINE

P0110 Intake Air Temperature Circuit

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010

DESCRIPTION

The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
The intake air temperature sensor is powered by a 5 V applied from the THA terminal of the ECM, via resistor R.
Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve drivability.
A056276E06

HINT:
When any of DTCs P0110, P0112 and P0113 are set, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.

DTC No.
Proceed to
DTC Detection Condition
Trouble Area
P0110
Step 1
Open or short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open or short in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter)
  3. ECM
P0112
Step 4
Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Short in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter)
  3. ECM
P0113
Step 2
Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter)
  3. ECM

HINT:
When any of these DTCs are set, check the intake air temperature by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit

WIRING DIAGRAM

A136106E06

INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    Same as actual intake air temperature.


    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Same as actual intake air temperature
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A140711E07
    Confirm the connection at mass air flow meter.

  1. Disconnect the mass air flow meter connector.

  1. Connect terminals THA and E2 of the mass air flow meter wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F) or higher

  1. Reconnect the mass air flow meter connector.



NG
Go to step 3
OK

REPLACE MASS AIR FLOW METER (Click here)

3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)

  1. A114608E18
    Confirm the connection at ECM.

  1. Disconnect the mass air flow meter connector.

  1. Connect terminals THA and E2 of the ECM connector.

    HINT:
    Before checking, do visual and contact pressure checks on the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F) or higher

  1. Reconnect the mass air flow meter connector.



NG
REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A084869E87
    Disconnect the mass air flow meter connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

  1. Reconnect the mass air flow meter connector.



NG
Go to step 5
OK

REPLACE MASS AIR FLOW METER (Click here)

5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)

  1. A114609E17
    Disconnect the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

  1. Reconnect the ECM connector.



NG
REPLACE ECM (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0102 Mass or Volume Air Flow Circuit Low Input (+ P0103) (from Jul 2010)P0110 Intake Air Temperature Circuit (+ P0112, P0113) (Aug 2008 – Jun 2010) →