2007-2013 Highlander Kluger · Service Manual ENGINE

P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

HINT:
These DTCs relate to the throttle position sensor.
This electronic throttle control system does not use a throttle cable.
The accelerator pedal position sensor is integrated with the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type, and uses Hall-effect elements, in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A019802E79
DTC No.
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. ECM
P0122
Output voltage of VTA1 is 0.2 V or less for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Short in VTA1 circuit
  3. Open in VC circuit
  4. ECM
P0123
Output voltage of VTA1 is 4.535 V or more for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Open in VTA1 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA1 circuits
  5. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. ECM
P0222
Output voltage of VTA2 is 1.75 V or less for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Short in VTA2 circuit
  3. Open in VC circuit
  4. ECM
P0223
Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V, for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Open in VTA2 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA2 circuits
  5. ECM
P2135
Either condition (a) or (b) is met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 0.5 V or less, for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  2. Throttle position sensor (built into throttle body)
  3. ECM

HINT:
  1. When any of these DTCs are set, check the throttle valve opening angle by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.
  2. Throttle Position No. 1 denotes the VTA1 signal (expressed in percentages), and Throttle Position No. 2 denotes the VTA2 signal (expressed in voltages).

Reference (Normal Condition): 
Tester Display
Accelerator Pedal Fully Released
Accelerator Pedal Fully Depressed
Throttle Position No. 1
0.5 to 1.1 V
3.3 to 4.9 V
Throttle Position No. 2
2.1 to 3.1 V
4.5 to 5.0 V

FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to electronic throttle control system malfunctions, are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed slowly, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A085458E29

INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ VALUE USING INTELLIGENT TESTER (THROTTLE POS AND THROTTLE POS #2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.

  1. Check the values displayed on the tester.

    Result:
    When Accelerator Pedal Released
    When Accelerator Pedal Depressed
    Trouble Area
    Proceed to
    Throttle Position No. 1 (VTA1)
    Throttle Position No. 2 (VTA2)
    Throttle Position No. 1 (VTA1)
    Throttle Position No. 2 (VTA2)
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    VC circuit open
    A
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    4.5 V to 5.0 V
    E2 circuit open
    0 V to 0.2 V, or 4.5 V to 5.0 V
    2.4 to 3.4 V (Fail-safe)
    0 V to 0.2 V, or 4.5 V to 5.0 V
    2.4 to 3.4 V (Fail-safe)
    VTA1 circuit open or ground short
    0.7 V to 1.3 V (Fail-safe)
    0 V to 0.2 V, or 4.5 V to 5.0 V
    0.7 V to 1.3 V (Fail-safe)
    0 V to 0.2 V, or 4.5 V to 5.0 V
    VTA2 circuit open or ground short
    0.5 V to 1.1 V
    2.1 V to 3.1 V
    3.3 V to 4.9 V (Not fail-safe)
    4.6 V to 5.0 V (Not fail-safe)
    Throttle position sensor circuit normal
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

  1. A168201E02
    Disconnect the throttle position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B27-5 (VC) - B1-23 (VC)
    Always
    Below 1 Ω
    B27-6 (VTA) - B1-20 (VTA)
    Always
    Below 1 Ω
    B27-4 (VTA2) - B1-19 (VTA2)
    Always
    Below 1 Ω
    B27-3 (E2) - B1-28 (E2)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B27-5 (VC) or B1-23 (VC) - Body ground
    Always
    10 kΩ or higher
    B27-6 (VTA) or B1-20 (VTA) - Body ground
    Always
    10 kΩ or higher
    B27-4 (VTA2) or B1-19 (VTA2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT ECM (VC VOLTAGE)

  1. A168199E15
    Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-23 (VC) - B1-28 (E2)
    Ignition switch on (IG)
    4.5 to 5.0 V



NG
REPLACE ECM (Click here)
OK


4. REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Replace the throttle with motor body assembly (Click here).


NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds or more.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)


← P0116 Engine Coolant Temperature Circuit Range / Performance Problem (from Jul 2010)P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit (+ 6 more codes) (Aug 2008 – Jun 2010) →