2007-2013 Highlander Kluger · Service Manual ENGINE

P0500 Vehicle Speed Sensor "A"

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU.
The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.
A079413E21
DTC No.
DTC Detection Condition
Trouble Area
P0500
Both of the following conditions (A) and (B) are met
(1 trip detection logic)
(A) Either of the following conditions 1 or 2 is met
  1. All of the following conditions (a), (b) and (c) are met
    1. Engine coolant temperature is 20°C (68°F) or more
    2. Engine coolant temperature sensor circuit malfunction is not detected
    3. Time after NSW input signal on to off is 2 seconds or more
  2. All of the following conditions (a), (b) and (c) are met
    1. Engine coolant temperature is less than 20°C (68°F)
    2. Engine coolant temperature sensor malfunction is detected
    3. Time after NSW input signal on to off is 30 seconds or more
(B) While vehicle is being driven, no vehicle speed sensor signal is sent to ECM
  1. Open or short in speed sensor circuit
  2. Speed sensor
  3. Combination meter
  4. ECM
  5. Skid control ECU

WIRING DIAGRAM

E211393E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in speedometer circuit.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speeds displayed on tester and speedometer display are equal.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

  1. E152386E17
    Remove the combination meter.

  1. Connect the oscilloscope to terminal E1-9 (+S) and body ground.

  1. Turn the ignition switch on (IG).

  1. Turn the wheel slowly.

  1. Check the signal waveform according to the condition(s) in the table below.

    Item
    Condition
    Tool setting
    5 V / DIV., 20 ms / DIV.
    Vehicle condition
    Driving at approx. 20 km/h (12 mph)

    OK:
    The waveform is displayed as shown in the illustration.

    Text in Illustration 
    *a
    Component with harness connected
    (Combination Meter Assembly)

    HINT:
    When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
GO TO SPEED SIGNAL CIRCUIT (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    E1-9 (+S) - D56-18 (SPD)
    Always
    Below 1 Ω

  1. Reconnect the combination meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0500 Vehicle Speed Sensor "A" (Aug 2008 – Jun 2010)P0504 Brake Switch "A" / "B" Correlation (+ P0724) (May 2007 – Jul 2008) →