2007-2013 Highlander Kluger · Service Manual ENGINE

P2102 Throttle Actuator Control Motor Circuit Low

Diagnostic trouble codes · Vehicles built May 2007 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jun 2010 from Jul 2010

DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using the gears.
The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:
This electronic throttle control system does not use a throttle cable.

DTC No.
DTC Detection Condition
Trouble Area
P2102
Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator duty ratio exceeds 80% or more
(b) Throttle actuator current is 0.5 A or less
  1. Open in throttle actuator circuit
  2. Throttle actuator
  3. ECM
P2103
Throttle actuator current is 7 A or more for 0.6 seconds (1 trip detection logic)
  1. Short in throttle actuator circuit
  2. Throttle actuator
  3. Throttle valve
  4. Throttle body
  5. ECM

FAIL-SAFE

When either of these DTCs, as well as other DTCs relating to electronic throttle control system malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed.
If the accelerator pedal is depressed gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

G041063E09

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  2. The throttle actuator current (Throttle Motor Close Duty ) and the throttle actuator duty ratio Throttle Motor Open Duty / Throttle Motor Close Duty) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.


1. INSPECT THROTTLE BODY (RESISTANCE OF THROTTLE CONTROL MOTOR)

  1. A159755E06
    Disconnect the throttle with motor body connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B27-2 (M+) - B27-1 (M-)
    20°C (68°F)
    0.3 to 100 Ω

  1. Reconnect the throttle with motor body connector.



NG
REPLACE THROTTLE BODY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (THROTTLE BODY - ECM)

  1. A168218E02
    Disconnect the throttle body connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B27-2 (M+) - B1-5 (M+)
    Always
    Below 1 Ω
    B27-1 (M-) - B1-4 (M-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B27-2 (M+) or B1-5 (M+) - Body ground
    Always
    10 kΩ or higher
    B27-1 (M-) or B1-4 (M-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT THROTTLE BODY
  1. Check for foreign objects between the throttle valve and the housing.

    OK:
    Normal



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY
OK


4. INSPECT THROTTLE VALVE
  1. Check if the throttle valve opens and closes smoothly.

    OK:
    The throttle valve opens and closes smoothly.



NG
REPLACE THROTTLE BODY (Click here)
OK

REPLACE ECM (Click here)


← P1660 VSV for AICVS Circuit (from Jul 2010)P2102 Throttle Actuator Control Motor Circuit Low (+ P2103) (from Jul 2010) →