2007-2013 Highlander Kluger · Service Manual ENGINE

P1660 VSV for AICVS Circuit

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010

DESCRIPTION

The air cleaner is equipped with 2 inlets, one of which is opened or closed by the air intake control valve. This system reduces intake noise and increases engine power at low to high engine speeds range.
When the engine is operating in the low-to-mid speed range, this control operates the air intake control valve to close one of the air cleaner inlets. When the engine speed is more than 3600 rpm and the opening angle of the throttle valve is more than 60°, the ECM activates the VSV and opens the air intake control valve.
A061332E15
DTC No.
Detection Condition
Trouble Area
P1660
The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
  1. Voltage of terminal AICV of the ECM is low when the vacuum switching valve for air intake control valve is OFF
  2. The engine has been started
  1. Open or short in air intake control valve circuit
  2. Vacuum switching valve for air intake control vale
  3. ECM

WIRING DIAGRAM

A207528E14

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VSV FOR AICV)
  1. Connect the intelligent tester to the DLC3.

  1. A067588E07
    Turn the ignition switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for AICS.

  1. Check the operation of the vacuum switching valve for air intake control valve when the vacuum switching valve for air intake control valve is operated by the tester.

    OK:
    Tester Operation
    Specified Condition
    VSV is ON
    Air from port E flows out through port F
    VSV is OFF
    Air from port E flows out through the air filter



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. CHECK NO. 3 INTAKE AIR CONTROL VALVE ASSEMBLY (VACUUM SWITCHING VALVE FOR AIR INTAKE CONTROL VALVE)
  1. Inspect the vacuum switching valve for air intake control valve (Click here).



NG
REPLACE NO. 3 INTAKE AIR CONTROL VALVE ASSEMBLY (VACUUM SWITCHING VALVE FOR AIR INTAKE CONTROL VALVE) (Click here)
OK


3. INSPECT TERMINAL VOLTAGE (VACUUM SWITCHING VALVE POWER SOURCE)

  1. A168222E18
    Disconnect the vacuum switching valve for air intake control valve connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A10-1 - Body ground
    Ignition switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vacuum Switching Valve for Air Intake Control Valve)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI NO. 3 FUSE - VACUUM SWITCHING VALVE)
OK


4. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE - ECM)
  1. Disconnect the vacuum switching valve for air intake control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A10-2 - B48-20 (AICV)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A10-2 or B48-20 (AICV) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the vacuum switching valve for air intake control valve connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VACUUM SWITCHING VALVE - ECM)
OK

REPLACE ECM (Click here)


← P1660 VSV for AICVS Circuit (May 2007 – Jun 2010)P2102 Throttle Actuator Control Motor Circuit Low (+ P2103) (May 2007 – Jun 2010) →