2007-2013 Highlander Kluger · Service Manual ENGINE

P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

CAUTION / NOTICE / HINT

HINT:
This DTC relates to the accelerator pedal position sensor.


DESCRIPTION

Refer to DTC P2120 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2121
Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic)
  1. Accelerator pedal position sensor
  2. ECM

FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to a normal condition.

WIRING DIAGRAM

Refer to DTC P2120 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION NO. 1 AND ACCELERATOR POSITION NO. 2)

  1. FI07052E14
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.

  1. Read the values displayed on the tester.

    Standard voltage:
    Accelerator Pedal Operation
    ACCELERATOR POSITION NO. 1 (AP#1)
    ACCELERATOR POSITION NO. 2 (AP#2)
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 4.7 V



NG
Go to step 3
OK


2. CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Select the following menu items on the tester: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2121
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)

3. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A168219E05
    Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A19-6 (VPA) - D31-18 (VPA)
    Always
    Below 1 Ω
    A19-5 (EPA) - D31-20 (EPA)
    Always
    Below 1 Ω
    A19-4 (VCPA) - D31-26 (VCPA)
    Always
    Below 1 Ω
    A19-3 (VPA2) - D31-19 (VPA2)
    Always
    Below 1 Ω
    A19-2 (EPA2) - D31-21 (EPA2)
    Always
    Below 1 Ω
    A19-1 (VCP2) - D31-27 (VCP2)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A19-6 (VPA) or D31-18 (VPA) - Body ground
    Always
    10 kΩ or higher
    A19-5 (EPA) or D31-20 (EPA) - Body ground
    Always
    10 kΩ or higher
    A19-4 (VCPA) or D31-26 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A19-3 (VPA2) or D31-19 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A19-2 (EPA2) or D31-21 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A19-1 (VCP2) or D31-27 (VCP2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE ACCELERATOR PEDAL
  1. Replace the accelerator pedal (Click here).


NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Select the following menu items on the tester: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2121
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)


← P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (from Jul 2010)P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (Aug 2008 – Jun 2010) →