2007-2013 Highlander Kluger · Service Manual ENGINE

P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

Refer to DTC P2120 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2121
Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic)
  1. Accelerator position sensor
  2. ECM

FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to limp mode. In limp mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to a normal condition.

WIRING DIAGRAM

Refer to DTC P2120 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2121 is output
    A
    P2121 and other DTCs are output
    B

    HINT:
    If any DTCs other than P2121 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEAL POSITION SENSOR)

  1. FI07052E41
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

  1. Read the values displayed on the tester.

    Standard voltage:
    Accelerator Pedal Operation
    Accel Sensor Out No. 1
    Accel Sensor Out No. 2
    Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    0.4 to 1.2 V
    Fully Depressed
    2.6 to 4.5 V
    3.4 to 5.0 V

    Text in Illustration 
    *a
    Depressed
    *b
    Released



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3. REPLACE ACCELERATOR PEDAL ASSEMBLY
  1. Replace accelerator pedal position sensor assembly (Click here).


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Fully depress and release the accelerator pedal.

  1. Check that 20 seconds or more have elapsed since the ignition switch was turned on (IG).

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2121
    A
    No output
    B



B
END
A

REPLACE ECM (Click here)


← P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (Aug 2008 – Jun 2010)P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) (+ P2196, P2197, P2198) (May 2007 – Jul 2008) →