2007-2013 Highlander Kluger · Service Manual ENGINE

P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.

The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.
The air fuel ratio sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter is used in order to convert the carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (HOx) into less harmful substances. To allow the three-way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio.
*: Value changes inside the ECM. Since the air fuel ratio sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.
A173183E01
DTC No.
DTC Detection Condition
Trouble Area
P2195
P2197
Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is more than 3.8 V
(b) Heated oxygen sensor voltage is 0.15 V or more
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor (bank 1, 2 sensor 1) heater
  4. Air induction system
  5. Fuel pressure
  6. ECM
P2195
P2197
While fuel-cut operation is performed (during vehicle deceleration), air fuel ratio sensor current is 3.6 mA or more for 3 seconds (2 trip detection logic)
  1. Air fuel ratio sensor
  2. ECM
P2196
P2198
Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor voltage is less than 2.8 V
(b) Heated oxygen sensor voltage is less than 0.6 V
  1. Open or short in air fuel ratio sensor (bank 1, 2 sensor 1) circuit
  2. Air fuel ratio sensor (bank 1, 2 sensor 1)
  3. Air fuel ratio sensor (bank 1, 2 sensor 1) heater
  4. Air induction system
  5. Fuel pressure
  6. ECM
P2196
P2198
While fuel-cut operation is performed (during vehicle deceleration), air fuel ratio sensor current is less than 1.4 mA for 3 seconds (2 trip detection logic)
  1. Air fuel ratio sensor
  2. ECM

HINT:
  1. DTCs P2195 and P2196 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
  2. DTCs P2197 and P2198 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.
  5. When any of these DTCs are set, check the air fuel ratio sensor voltage output by selecting the following menu items on the intelligent tester: Powertrain Engine and ECT / Data List / A/F Control System / AFS B1S1 or AFS B2S1.
  6. Short-term fuel trim values can also be read using the intelligent tester.
  7. The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the intelligent tester.
  8. If an air fuel ratio sensor malfunction is detected, the ECM sets a DTC.


WIRING DIAGRAM

A172770E02

CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in steps 3, 6 and 13 of the following diagnostic troubleshooting procedure when using the intelligent tester.
G039003E22
G034990E07
  1. Connect the intelligent tester to the DLC3 (Procedure "A").
  2. Turn the ignition switch on (IG) (Procedure "B").
  3. Turn the tester on (Procedure "C").
  4. Clear the DTCs (Click here) (Procedure "D").
  5. Start the engine, and warm it up until the ECT reaches 70°C (158°F) or higher (Procedure "E").
  6. Select the following menu items on the tester to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut (Procedure "F").
  7. Drive the vehicle at between 60 km/h (38 mph) and 120 km/h (75 mph) for at least 10 minutes (Procedure "G").
  8. Change the transmission to the 2nd gear (Procedure "H").
  9. Drive the vehicle at a proper vehicle speed to perform fuel-cut operation (refer to the following HINT) (Procedure "I").

    HINT:
    Fuel-cut is performed when the following conditions are met:
    1. Accelerator pedal is fully released.
    2. Engine speed is 2500 rpm or more (fuel injection resumes at 1000 rpm).

  10. Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds (Procedure "J").
  11. Soon after performing procedure "J" , release the accelerator pedal for at least 4 seconds without depressing the brake pedal, in order to execute fuel-cut control (Procedure "K").
  12. Allow the vehicle to decelerate until the vehicle speed declines to less than 10 km/h (6 mph) (Procedure "L").
  13. Repeat procedures from "H" through "K" in this section at least 3 times per driving cycle (Procedure "M").

    HINT:
    Completion of all air fuel ratio sensor monitors is required to change the value in TEST RESULT.

    CAUTION:
    Strictly observe posted speed limits, traffic laws, and road conditions when performing these driving patterns.


INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

  1. The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using an intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Start the engine and turn the tester on.
    3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
    4. Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the Right or Left button to change the fuel injection volume).
    6. Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

      HINT:
      1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
      2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


      Standard voltage:
      Tester Display (Sensor)
      Injection Volume
      Status
      Voltage
      AFS B1S1 or AFS B2S1 (Air fuel ratio)
      +25%
      Rich
      Less than 3.0
      AFS B1S1 or AFS B2S1 (Air fuel ratio)
      -12.5%
      Lean
      More than 3.35
      O2S B1S2 or O2S B2S2 (Heated oxygen)
      +25%
      Rich
      More than 0.55
      O2S B1S2 or O2S B2S2 (Heated oxygen)
      -12.5%
      Lean
      Less than 0.4

      NOTICE:
      The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

      Case
      Air Fuel Ratio Sensor (Sensor 1)
      Output Voltage
      Heated Oxygen Sensor (Sensor 2)
      Output Voltage
      Main Suspected Trouble Area
      1
      A162605E01
      A162598E02
      -
      2
      A162596E01
      A162598E02
      1. Air fuel ratio sensor
      2. Air fuel ratio sensor heater
      3. Air fuel ratio sensor circuit
      3
      A162605E01
      A162596E01
      1. Heated oxygen sensor
      2. Heated oxygen sensor heater
      3. Heated oxygen sensor circuit
      4
      A162596E01
      A162596E01
      1. Fuel pressure
      2. Gas leakage from exhaust system
        (Air fuel ratio extremely lean or rich)
    1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
    2. The following air fuel ratio control procedure enables the technician to check and graph the voltage output of both the heated oxygen sensors. To display the graph, select the following menu items on the tester: View / Line Graph.

      HINT:
      1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
      2. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
      3. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2195, P2196, P2197 or P2198
    A
    P2195, P2196, P2197 or P2198 and other DTCs
    B

    HINT:
    If any DTCs other than P2195, P2196, P2197 or P2198 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.

  1. Select the following menu items on the tester: Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1S1 or AFS B2S1 and Engine Speed.

  1. Check the air fuel ratio sensor voltage 3 times, when the engine is in each of the following conditions:

    1. While idling (check for at least 30 seconds) (Step (1))

    2. At an engine speed of approximately 2500 rpm (without any sudden changes in engine speed) (Step (2))

    3. Raise the engine speed to 4000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed (Step (3)).

      Standard voltage:
      Condition
      Air Fuel Ratio Sensor Voltage Variation
      Reference
      Steps (1) and (2)
      Changes at approximately 3.3 V
      Between 3.1 V and 3.5 V
      Step (3)
      Increases to 3.8 V or more
      This occurs during engine deceleration (when fuel-cut performed)

      HINT:
      For more information, see the diagrams below.

      A072304E27

      HINT:
      1. If the output voltage of the air fuel ratio sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those described on the previous page, the air fuel ratio sensor may have an open circuit. (This will also happen if the air fuel ratio sensor heater has an open circuit.)
      2. If the output voltage of the air fuel ratio sensor remains at either approximately 3.8 V or more, or 2.8 V or less (see Malfunction Condition diagram) under any conditions, including those described on the previous page, the air fuel ratio sensor may have a short circuit.
      3. The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the air fuel ratio sensor output voltage.
      4. The ECM must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 16 km/h (10 mph) to allow the ECM to learn the closed throttle valve position.
      5. When the vehicle is driven:
        The output voltage of the air fuel ratio sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The air fuel ratio sensor is functioning normally.
      6. The air fuel ratio sensor is a current output element; therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the air fuel ratio sensor or ECM will show a constant voltage result.



NG
Go to step 8
OK


3. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Read the DTCs using the intelligent tester.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198 (air fuel ratio sensor pending DTCs)
    B



B
Go to step 15
A


5. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


6. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


7. CHECK WHETHER DTC OUTPUT RECURS
  1. Read the DTCs using the intelligent tester.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198
    B



B
REPLACE ECM (Click here)
A

END

8. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

  1. A126269E39
    Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


9. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

  1. A136175E14
    Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) - B2-2 (HA1A)
    Always
    Below 1 Ω
    B20-3 (A1A+) - B2-22 (A1A+)
    Always
    Below 1 Ω
    B20-4 (A1A-) - B2-30 (A1A-)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) - B2-1 (HA2A)
    Always
    Below 1 Ω
    B19-3 (A2A+) - B2-23 (A2A+)
    Always
    Below 1 Ω
    B19-4 (A2A-) - B2-31 (A2A-)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B20-1 (HA1A) or B2-2 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B20-3 (A1A+) or B2-22 (A1A+) - Body ground
    Always
    10 kΩ or higher
    B20-4 (A1A-) or B2-30 (A1A-) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B19-1 (HA2A) or B2-1 (HA2A) - Body ground
    Always
    10 kΩ or higher
    B19-3 (A2A+) or B2-23 (A2A+) - Body ground
    Always
    10 kΩ or higher
    B19-4 (A2A-) or B2-31 (A2A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the air fuel ratio sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage.

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


11. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


12. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


13. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


14. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
  1. Read the DTCs using the intelligent tester.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P2195, P2196, P2197 or P2198
    B



B
REPLACE ECM (Click here)
A

END

15. CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
CHECK INTERMITTENT PROBLEMS
YES

DTC CAUSED BY RUNNING OUT OF FUEL


← P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (from Jul 2010)P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) (+ P2196, P2197, P2198) (Aug 2008 – Jun 2010) →