2007-2013 Highlander Kluger · Service Manual BODY

ADJUSTMENT

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:

  1. B174181E02
    Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.
  3. Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.
  4. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. PRECAUTION

NOTICE:
  1. For the glass hatch type, if the back door adjustment is performed, the location of the axis of the rear wiper motor assembly will change, causing the wiping angle to change. Be sure to remove and install the rear wiper motor assembly using the centering jig.
  2. Do not open the glass hatch before installing the rear wiper link pivot.


2. REMOVE DECK BOARD ASSEMBLY

  1. B173240
    Remove the deck board assembly.


3. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Disengage the 2 guides and remove the No. 3 deck board sub-assembly.


4. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Disengage the 2 guides and remove the No. 2 deck board sub-assembly.


5. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.


6. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Disengage the 3 clips and 3 guides, and remove the rear No. 1 floor board.


7. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Disengage the 2 clips and remove the rear seat side cover LH.


8. REMOVE DECK SIDE TRIM BOX LH

  1. B173243E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box LH as shown in the illustration.

    B178554


9. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Disengage the 2 clips and remove the rear seat side cover RH.


10. REMOVE JACK CARRIER SUPPORT

11. REMOVE JACK CARRIER CUSHION (for LHD)

  1. B178550
    Remove the jack carrier cushion.


12. REMOVE JACK CARRIER CUSHION (for RHD)

  1. B178551
    Remove the jack carrier cushion.


13. REMOVE JACK ASSEMBLY (for LHD)

  1. B173245
    Remove the jack assembly.


14. REMOVE JACK ASSEMBLY (for RHD)

  1. B178566
    Remove the jack assembly.


15. REMOVE JACK CARRIER ASSEMBLY (for LHD)

  1. B178548
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


16. REMOVE JACK CARRIER ASSEMBLY (for RHD)

  1. B179785
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


17. REMOVE DECK SIDE TRIM BOX RH

  1. B173247E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box RH as shown in the illustration.

    B178552


18. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.


19. REMOVE REAR MAT

  1. B173249
    Remove the rear mat.


20. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B260042
    Disengage the 3 claws.

  1. Remove the 2 nuts and deck floor board assembly.


21. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Remove the 2 nuts and the deck floor box.


22. REMOVE REAR FLOOR FINISH PLATE

  1. B173609
    Disengage the 4 clips and 4 claws, and remove the rear floor finish plate.


23. ADJUST BACK DOOR PANEL SUB-ASSEMBLY

  1. B174185
    Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.

  1. Tighten the body side hinge after the adjustment.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. B174182
    Adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic hammer.

  1. Tighten the striker mounting screws after the adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


24. INSTALL REAR FLOOR FINISH PLATE

  1. B173609
    Engage the 4 clips and 4 claws, and install the rear floor finish plate.


25. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Install the rear deck floor box with the 2 nuts.


26. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Install the 2 nuts and deck floor board assembly.

  1. Engage the 3 claws.


27. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


28. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B260042
    Install the rear deck floor board assembly with the 4 nuts and 4 bolts.


29. INSTALL DECK SIDE TRIM BOX LH

  1. Install the deck side trim box LH as shown in the illustration.

    B178555

  1. B173243E01
    Install the 2 deck side trim clips and clip.


30. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Engage the 2 clips and install the rear seat side cover LH.


31. INSTALL DECK SIDE TRIM BOX RH

  1. Install the deck side trim box RH as shown in the illustration.

    B178553

  1. B173247E01
    Install the 2 deck side trim clips and clip.


32. INSTALL JACK CARRIER ASSEMBLY (for LHD)

  1. B178549
    Engage the 3 claws, and install the jack carrier assembly.


33. INSTALL JACK CARRIER ASSEMBLY (for RHD)

  1. B179786
    Engage the 3 claws, and install the jack carrier assembly.


34. INSTALL JACK ASSEMBLY (for LHD)

  1. B173245
    Install the jack assembly.


35. INSTALL JACK ASSEMBLY (for RHD)

  1. B178566
    Install the jack assembly.


36. INSTALL JACK CARRIER CUSHION (for LHD)

  1. B178550
    Install the jack carrier cushion.


37. INSTALL JACK CARRIER CUSHION (for RHD)

  1. B178551
    Install the jack carrier cushion.


38. INSTALL JACK CARRIER SUPPORT

39. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Engage the 2 clips and install the rear seat side cover RH.


40. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Engage the 3 guides and 3 clips and install the rear No. 1 floor board.


41. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

42. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


43. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


44. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board assembly.


45. REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY

  1. B173198
    Disengage the 4 clips and 4 claws, and remove the back window upper trim panel assembly.


46. REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door)

  1. B173199
    Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.


47. REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

  1. B173200
    Disengage the 6 claws, and remove the back door service hole cover LH.


48. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)

  1. B173201
    Disconnect the power back door rod and remove the back door stay plate.


49. REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door)

  1. B173202
    Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.


50. REMOVE BACK DOOR TRIM COVER RH

  1. B174214
    Disengage the 2 clips and 2 claws, and remove the back door trim cover RH.


51. REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type)

  1. B173203
    Disengage the 2 claws and 4 guides, and remove the back door lock cover.


52. REMOVE ASSIST STRAP HOLE COVER

  1. B177265
    Disengage the 2 claws and 2 guides, and remove the assist strap hole cover.


53. REMOVE ASSIST STRAP ASSEMBLY

  1. B177264
    Remove the bolt and assist strap assembly.


54. REMOVE BACK DOOR TRIM PANEL ASSEMBLY

  1. B174211
    Disengage the 16 clips and remove the back door trim panel assembly.


55. REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type)

  1. E151098
    Disengage the 3 clips and remove the rear wiper shaft cover.


56. REMOVE REAR WIPER ARM HEAD CAP

  1. E150155
    Remove the rear wiper arm head cap.


57. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

  1. E150156
    Remove the nut and the rear wiper arm and blade assembly.


58. REMOVE REAR WIPER LINK CAP (for Glass Hatch Type)

  1. E150157
    Remove the rear wiper link cap.


59. REMOVE REAR WIPER LINK PIVOT (for Glass Hatch Type)

  1. E150158
    Remove the nut and the rear wiper link pivot.


60. REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)

  1. When reinstalling the rear wiper motor assembly:

    1. Open the glass hatch.

    2. E154835
      Engage the 3 claws and 2 guides, and then install the centering jig.

      NOTICE:
      1. The centering jig cannot be reused.
      2. Do not remove the centering jig before installing the rear wiper link pivot.

    3. E152621
      Close the glass hatch, and engage the 2 claws and guide.

      NOTICE:
      Be sure to engage the 2 claws and guide securely.

    4. E151099
      Disconnect the connector.

    5. Remove the 2 nuts.

    6. Remove the 4 bolts and the rear wiper motor assembly.

      NOTICE:
      1. Do not hold the rear wiper motor assembly by the rear wiper link pivot.
      2. Be careful not to scratch the back door glass.

  1. When using a new rear wiper motor assembly:

    1. E150159
      Disconnect the connector.

    2. Remove the 4 bolts.

    3. E150183
      Remove the 2 nuts and the rear wiper motor assembly.

      NOTICE:
      Be careful not to scratch the back door glass.


61. INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)

  1. E151099E01
    Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.

    NOTICE:
    1. Do not hold the rear wiper motor assembly by the rear wiper link pivot.
    2. Be careful not to scratch the back door glass.
    3. Do not remove the centering jig before installing the rear wiper link pivot.

  1. Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.

    Torque:
    Bolt:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
    Nut:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.


62. INSTALL REAR WIPER LINK PIVOT (for Glass Hatch Type)

  1. E150158
    Install the rear wiper link pivot with the nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Open the glass hatch.

  1. E154835
    Disengage the 2 guides.

  1. Disengage the 3 claws and remove the centering jig.

  1. Close the glass hatch.


63. INSTALL REAR WIPER LINK CAP (for Glass Hatch Type)

  1. E150184E01
    Apply MP grease to the entire surface of the rear wiper link cap.

    HINT:
    Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

  1. E150157
    Install the rear wiper link cap.


64. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Glass Hatch Type)
  1. Stop the wiper motor at the automatic stop position.

  1. E112237E01
    When reinstalling:

    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E150194E01
    Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.
    Area
    Dimension
    A
    10 mm (0.39 in.)

  1. Install the rear wiper arm and blade assembly with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Hold down the wiper arm by hand when tightening the nut.


65. INSTALL REAR WIPER ARM HEAD CAP

  1. E150155
    Install the rear wiper arm head cap.

    HINT:
    Push down on the cap until a click sound can be heard.


66. INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type)
  1. Open the glass hatch.

  1. E151098
    Engage the 3 clips and install the rear wiper shaft cover.

  1. Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.


67. INSTALL BACK DOOR TRIM PANEL ASSEMBLY

  1. B174211
    Engage the 16 clips and install the back door trim panel assembly.


68. INSTALL ASSIST STRAP ASSEMBLY

  1. B177264
    Install the assist strap assembly with the bolt.


69. INSTALL ASSIST STRAP HOLE COVER

  1. B177265
    Engage the 2 guides and 2 claws, and install the assist strap hole cover.


70. INSTALL BACK DOOR LOCK COVER (for Glass Hatch Type)

  1. B173203
    Engage the 4 guides and 2 claws, and install the back door lock cover.


71. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door)

  1. B173199
    Engage the 2 clips and 2 claws, and install the back door trim cover LH.


72. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door)

  1. B173202
    Engage the 2 clips and 2 claws, and install the back door trim cover LH.


73. CONNECT POWER BACK DOOR ROD (w/ Power Back Door)

  1. B173201
    Install the back door stay plate and connect the power back door rod.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


74. INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

  1. B173200
    Engage the 6 claws and install the back door service hole cover LH.


75. INSTALL BACK DOOR TRIM COVER RH

  1. B174214
    Engage the 2 clips and 2 claws, and install the back door trim cover RH.


76. INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY

  1. B173198
    Engage the 4 clips and 4 claws, and install the back window upper trim panel assembly.

← ADJUSTMENT (Aug 2008 – Jun 2010)REASSEMBLY (May 2007 – Jul 2008) →