2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

B1422/22 Compressor Lock Sensor Circuit

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier via CAN communication.
The air conditioning amplifier reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier determines that the compressor is locked, and turns the magnetic clutch off.
DTC No.
DTC Detection Condition
Trouble Area
B1422/22
Open or short in compressor lock sensor circuit
  1. Air conditioning compressor (Air conditioning lock sensor)
  2. Compressor drive belt
  3. Harness or connector between compressor and air conditioning amplifier
  4. Air conditioning amplifier
  5. CAN communication system

WIRING DIAGRAM

E154278E04

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    OK:
    CAN DTC is not output.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


2. INSPECT AIR CONDITIONING AMPLIFIER

  1. E124471E42
    Remove the air conditioning amplifier with the connectors still connected.

  1. E116941E03
    Measure the waveform of the connector.
    Item
    Contents
    Tool setting
    200 mV/DIV., 10 ms./DIV.
    Vehicle condition
    Engine is running
    A/C switch: ON
    Blower switch: LO

    Standard:
    Tester Connection
    Condition
    Specified Condition
    D33-8 (LOCK) - D33-13 (SG-2)
    Engine is running
    A/C switch: ON
    Blower switch: LO
    Pulse generation

    Result:
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


3. INSPECT COMPRESSOR AND MAGNETIC CLUTCH (AIR CONDITIONING LOCK SENSOR)

  1. E152688E06
    Disconnect the connector from the air conditioning compressor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B44-2 (SSR+) - B44-5 (SSR-)
    20°C (68°F)
    160 to 320 Ω



NG
REPLACE COMPRESSOR AND MAGNETIC CLUTCH (AIR CONDITIONING LOCK SENSOR) (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONING LOCK SENSOR)

  1. E143742E88
    Disconnect the connector from the air conditioning amplifier.

  1. E152687E06
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D33-8 (LOCK) - B44-2 (SSR+)
    Always
    Below 1 Ω
    D33-13 (SG-2) - B44-5 (SSR-)
    Always
    Below 1 Ω
    D33-8 (LOCK) - Body ground
    Always
    10 kΩ or higher
    D33-13 (SG-2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)


← B1417/17 Rear Evaporator Temperature Sensor Circuit (from Jul 2010)B1422/22 Compressor Lock Sensor Circuit (Aug 2008 – Jun 2010) →