2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1627/82 Lost communication with Side Airbag Sensor LH

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.
The side airbag sensor LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).
DTC No.
DTC Detection Condition
Trouble Area
B1627/82
B1628/82
B1637/82
B1638/82
B1647/82
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).
  2. Side airbag sensor LH malfunction
  3. Rear airbag sensor LH malfunction
  4. Center airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Side airbag sensor LH
  3. Rear airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM

C165789E39

INSPECTION PROCEDURE


1. CHECK PRESENT DTC
  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for present DTCs (Click here).

    Result:
    Result
    Proceed to
    Present DTC B1628 is output.
    A
    Present DTC B1647 or 82 is output.
    B
    Present DTC B1637 or B1638 is output.
    C
    Present DTC B1627 is output.
    D
    Present DTC B1627, B1628, B1637, B1638, B1647 or 82 is not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then on (IG) again.
    2. Codes other than DTCs B1627, B1628, B1637, B1638, B1647 and 82 may be output at this time, but they are not related to this check.



B
Go to step 3

C
Go to step 14

D
Go to step 21

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2. CHECK PAST DTC
  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for past DTCs (Click here).

    Result:
    Result
    Proceed to
    Past DTC B1627 or B1637 is not output.
    A
    Past DTC B1637 is output.
    B
    Past DTC B1627 is output.
    C

    HINT:
    Codes other than past DTCs B1627 and B1637 may be output at this time, but they are not related to this check.



B
Go to step 14

C
Go to step 21
A


3. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, side airbag sensor LH and rear airbag sensor LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


4. CHECK NO. 2 FLOOR WIRE (OPEN)

  1. Using SST, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.C203026E09

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-4 (BBL+) - O41-3 (BBL-)
    Always
    Below 1 Ω



NG
REPLACE NO. 2 FLOOR WIRE
OK


5. CHECK NO. 2 FLOOR WIRE (SHORT)

  1. C203027E08
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-4 (BBL+) - O41-3 (BBL-)
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


6. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

  1. C203027E08
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-4 (BBL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O41-3 (BBL-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE NO. 2 FLOOR WIRE
OK


7. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

  1. C203027E08
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    O41-3 (BBL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


8. CHECK NO. 2 FLOOR WIRE (OPEN)

  1. Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.C213490E08

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-1 (BCL+) - O41-2 (BCL-)
    Always
    Below 1 Ω



NG
REPLACE NO. 2 FLOOR WIRE
OK


9. CHECK NO. 2 FLOOR WIRE (SHORT)

  1. C213489E08
    Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-1 (BCL+) - O41-2 (BCL-)
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


10. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

  1. C213489E08
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (BCL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O41-2 (BCL-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE NO. 2 FLOOR WIRE
OK


11. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

  1. C213489E08
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O41-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


12. CHECK SIDE AIRBAG SENSOR LH

  1. C166120E01
    Connect the connectors to the rear airbag sensor LH and center airbag sensor assembly.

  1. Interchange the side airbag sensor RH with the side airbag sensor LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1628, B1647 or 82 is output.
    A
    DTC B1623, B1642 or 81 is output.
    B
    DTCs B1623, B1642 or 81 and B1628, B1647 or 82 are not output.
    C

    HINT:
    Codes other than DTCs B1623, B1642 or 81 and B1628, B1647 or 82 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


13. CHECK REAR AIRBAG SENSOR LH

  1. C166174E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and side airbag sensor LH to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1623, B1642 or 81 and B1628, B1647 or 82 are not output.
    A
    DTC B1628, B1647 or 82 is output.
    B
    DTC B1623, B1642 or 81 is output.
    C

    HINT:
    Codes other than DTCs B1623, B1642 or 81 and B1628, B1647 or 82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

14. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor LH and rear airbag sensor LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


15. CHECK NO. 2 FLOOR WIRE (OPEN)

  1. Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.C213490E08

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-1 (BCL+) - O41-2 (BCL-)
    Always
    Below 1 Ω



NG
REPLACE NO. 2 FLOOR WIRE
OK


16. CHECK NO. 2 FLOOR WIRE (SHORT)

  1. C213489E08
    Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-1 (BCL+) - O41-2 (BCL-)
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


17. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

  1. C213489E08
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (BCL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O41-2 (BCL-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE NO. 2 FLOOR WIRE
OK


18. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

  1. C213489E08
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O41-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O41-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE NO. 2 FLOOR WIRE
OK


19. CHECK SIDE AIRBAG SENSOR LH

  1. C166120E01
    Connect the connector to the rear airbag sensor LH.

  1. Interchange the side airbag sensor RH with the side airbag sensor LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1637 or B1638 is output.
    A
    DTC B1632 or B1633 is output.
    B
    DTCs B1632 or B1633 and B1637 or B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


20. CHECK REAR AIRBAG SENSOR LH

  1. C166174E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and side airbag sensor LH to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1632 or B1633 and B1637 or B1638 are not output.
    A
    DTC B1637 or B1638 is output.
    B
    DTC B1632 or B1633 is output.
    C

    HINT:
    Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

21. CHECK SIDE AIRBAG SENSOR LH

  1. C166120E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Interchange the side airbag sensor RH with the side airbag sensor LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1622 and B1627 are not output.
    A
    DTC B1627 is output.
    B
    DTC B1622 is output.
    C

    HINT:
    Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1625/22 Front Passenger Side - Side Airbag Sensor Malfunction (Aug 2008 – Jun 2010)B1627/82 Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly (+ 5 more codes) (May 2007 – Jul 2008) →